659475
9
Zoom out
Zoom in
Previous page
1/192
Next page
9
RFP-3907-E
GBR
To operate the dicer
1. Place a large bowl on a at stable horizontal surface.
2.
Fit the removable dicer attachment at the attachment hole. Note: the
blade is very sharp, handle with caution! Always hold the blade by the
plastic collar. Connect horizontal blade to the attachment, holding it by
the plastic collar.
3. Fit the dicer onto the bowl. Ensure the dicer is properly xed.
4.
Fit the lid onto the bowl, aligning the crosspiece of the plastic collar with
the corresponding notches in the center of the lid. Align the projections
on the sides of the lid with the corresponding notches on the bowl
edges. Gently press the lid down and rotate clockwise until it clicks into
place.
5.
Press and hold both xation buttons simultaneously and connect the
motor unit with the xation hole on the bowl lid.
6.
Plug in the appliance. Select the speed setting: harder foods require
higher dicing speed. Turn the speed control knob clockwise to increase
the speed.
7.
Gently put food into the bowl through the food supply slot, using the
pusher bar.
DO NOT push food by hands or other objects to avoid injuries or appliance
breakdown!
8. Holding the bowl by one hand, press and hold the Power or Turbo mode
button. Use Turbo mode for meat and other tough foods.
9. Unplug the appliance after use. Press and hold both xation buttons si-
multaneously and disconnect the motor unit. Press the button on the
bowl handle and turn the lid simultaneously counterclockwise to remove.
10.
Remove the appliance from the bowl and carefully remove horizontal
blade and removable section, holding by plastic details.
11. Clean the appliance in accordance with table A1.
To operate the slicer
1. Place a large bowl on a at stable horizontal surface.
2. Fit the removable collar on a central pin at the bottom of the chopper
bowl. Fit the slicer onto the collar. Note: the blade is very sharp, handle
with caution!
3.
Fit the lid onto the bowl, aligning the crosspiece of the plastic collar with
the corresponding notches in the center of the lid. Align the projections
on the sides of the lid with the corresponding notches on the bowl
edges. Gently press the lid down and rotate clockwise until it clicks into
place.
4.
Press and hold both xation buttons simultaneously and connect the
motor unit with the xation hole on the bowl lid.
5.
Plug in the appliance. Select the speed setting: harder foods require
higher dicing speed. Turn the speed control knob clockwise to increase
the speed.
6. Gently put food into the bowl through the feed hole, using the pusher bar.
DO NOT push food by hands or other objects to avoid injuries or the appliance
breakdown!
7. Holding the bowl by one hand, press and hold the Power or Turbo mode
button. Use Turbo mode for meat and other tough foods.
8. Unplug the appliance after use. Press and hold both xation buttons si-
multaneously and disconnect the motor unit. Press the button on the
bowl handle and turn the lid simultaneously counterclockwise to remove.
9. Carefully remove the slicer and removable collar from the chopper bowl.
10. Clean the appliance in accordance with table A1.
III. BEFORE CONTACTING SERVICE CENTER
Problem Possible causes and solutions
Appliance does
not work
The power cord is not connected to an electrical outlet, voltage failure in
electrical outlet. Connect the power cord to an electric network. Connect the
appliance to properly working electrical outlet.
Strong vibration
during operation
Food pieces are too large. Cut food into smaller pieces
Plastic smell dur-
ing use
The appliance is overheated. Reduce continuous operation time. Increase
intervals between switching.
The appliance is new; the smell is coming from protective cover. Thoroughly
clean the appliance (ref. table A1).The smell will disappear after few uses.
IV. PRODUCT WARRANTY
We warrant this product to be free from defects for a period of 2 years from the
date of purchase. If the appliance fails to operate properly within the warranty
period and is found to be defective in material or workmanship, we will repair or
replace it free of charge. This warranty comes into force only in case an original
warranty service coupon with a serial article number and an accurate impress of
the company of the seller proves the purchase date. This limited warranty does
not cover damage caused by the failure to use this product for its normal purpose
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Redmond RFP-3907-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Redmond RFP-3907-E in the language / languages: All languages as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info