Manual Redmond RFP-3907-E (page 8 of 192) (All languages)

659475

Zoom out

Zoom in

1/192

I. BEFORE THE FIRST USE

Carefully remove the unit and its accessories from the packaging. Dispose of

all packaging materials and promotional stickers.

Keep all warning labels and the serial number identication label located on the

housing. The absence of the serial number will deprive you of your warranty benets!

Unwind the power cord. Wipe the housing with a damp cloth. Wash removable

parts with warm soapy water and dry thoroughly before connecting the appliance

to an electrical outlet.

After transporting or storing at low temperatures allow the appliance to stay

at room temperature for at least 2 hours before using.

II. OPERATING THE HAND BLENDER

General Guidelines

• Do not ll the food vessel more than 2/3 full to prevent splattering.

• When using the whisk or blending attachment place the attachment into

food rst and then press the Power of Turbo mode button. Always release

the button before removing the hand blender from the vessel.

• Start operating at a low speed and gradually increase it by rotating the

speed control knob on the handle. The control knob has a dial: select an

optimal operating speed setting by rotating the speed control knob.

• To process at a maximum speed (when blending tough ingredients or for

the nal whipping stage) press and hold down the Turbo mode button.

Do not immerse the blender above the joint between the motor unit and the

attachment.

•

Defrost, de-bone, clean, and cut meat into 1-1.5 cm cubes before processing.

• Remove the pits and cut fruits and berries into pieces before processing.

• Do not use the hand blender to mash potatoes.

•

Remove the pot from the stove top and let cool down before processing hot

foods. Do not process any food or liquid at a temperature higher than 80°C.

Start processing at a low speed to avoid splatter. Do not use the blender to

process coffee beans, ice cubes, sugar, grain, beans, and other tough foods.

Do not use the chopper bowl for blending or whisking. The central pin at the

bottom of the chopper bowl can damage the attachment. Use the beaker

provided with the appliance.

To operate the whisk

1. Fill the beaker or a similar vessel with food.

2. Insert the whisk attachment to gear box until it clicks into place.

Press and hold both attachment xation buttons simultaneously. Connect

the whisk attachment to the motor unit and turn counterclockwise until

it clicks into place.

4. Plug in the appliance. Turn the speed control knob counterclockwise to

setting 1 (minimum speed).

Hold the vessel steady and place the whisk attachment in food. Press and

hold down the Power button. Turn the speed control knob clockwise to

increase the speed if necessary (from 1 to 5). To whisk at a maximum

speed press and hold down the Turbo mode button.

6. Whisk foods using clockwise circular motion.

7. After use unplug the appliance. Press and hold the attachment xation

buttons simultaneously and gently disconnect the whisk attachment.

8. Clean the appliance in accordance with the table A1.

To operate the chopper

1. Place a large or a small bowl on a at stable horizontal surface.

Fit the S-shaped blade on a central pin at the bottom of the chopper

bowl. Note: the blade is very sharp, handle with caution! Always hold the

blade by the plastic collar.

3. Fill the bowl with food. Do not ll above the maximum ll mark. Follow

the procedures outlined in “General Guidelines” section.

4. Fit the lid onto the bowl, aligning the crosspiece of the plastic collar with

the corresponding notches in the center of the lid. Align the projections

on the sides of the lid with the corresponding notches on the bowl edges.

Gently press the lid down and rotate clockwise until it clicks into place.

Press and hold both xation buttons simultaneously and connect the

motor unit with the xation hole on the bowl lid.

Plug in the appliance. Select the speed setting: harder foods require

higher chopping speed.

Turn the speed control knob clockwise to increase the speed. Steadily

holding the vessel with one hand press and hold down the Power or Turbo

mode button. Use Turbo mode for meat and other tough foods.

8. After use unplug the appliance. Press and hold both xation buttons si-

multaneously and disconnect the motor unit. If you used the large bowl,

press the button on the bowl handle and turn the lid simultaneously

counterclockwise to remove.

9. Remove the S-shaped blade holding it by the plastic collar.

10. Clean the appliance in accordance with the table A1.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Redmond RFP-3907-E in the language / languages: All languages as an attachment in your email.

The manual is 2,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Redmond RFP-3907-E Manual

Product: