597828
173
Zoom out
Zoom in
Previous page
1/183
Next page
RED DSMC OPERATION GUIDE: WEAPON
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-E | 173
LENSES
This section describes lenses and lens operations for the DSMC system.
WARNING: All lenses are hot swappable. However, lens mounts are NOT HOT SWAPPABLE, meaning you cannot
remove or install lens mounts while the camera is turned on. Before installing or removing lens mounts, you
MUST turn off the camera. Failure to do so may result in damage to the lens mounts or DSMC that will not be
covered under warranty.
LENS WEIGHT AND LENS SUPPORT
Use a lens support system when mounting heavy or long lenses to your camera.
When mounting a heavy or long lens, ensure that the full weight of the lens is never directly on the camera or
lens mount. Mount the lens to the support system first, and then carefully mount the lens to the camera.
Due to the lightweight construction of the carbon fiber BRAIN and magnesium mounts, most setups with the
carbon fiber BRAIN require a lens support system for all but the lightest lenses.
WARNING: Failure to use lens supports appropriate for the lens and camera setup may lead to damage of the
DSMC and lens mount. Any damage caused by not using a lens support system will not be covered under
warranty.
POSITIVE LOCK (PL) LENSES
This section describes the appropriate method for attaching and detaching PL lenses. For more information,
refer to the original manufacturer’s instructions. This section also lists lenses supported by the DSMC PL
mounts.
WARNING: ALWAYS protect your equipment, when it is not in use, by replacing lens caps and mount caps.
ATTACH PL LENSES
1. Rotate the locking ring counter-clockwise to release the DSMC mount cap.
2. Remove the rear lens cap and the DSMC mount cap.
3. Align the key and contact pads (if present) on the PL lens with the key and connector pins on the DSMC
PL mount.
4. Insert the lens into the DSMC PL mount.
5. Rotate the locking ring clockwise to secure the lens in place.
DETACH PL LENSES
1. Rotate the locking ring counter-clockwise to release the PL lens.
2. Remove the PL lens from the DSMC PL mount.
3. Replace the rear lens cap and DSMC mount cap when the lens is not in use.
DSMC PL MOUNT SUPPORTED LENSES
The DSMC Mg PL Mount 2.0, DSMC TI PL Mount, and the RED MOTION MOUNT Ti PL are compatible with
most standard PL mount cinema lenses and devices. For information about the compatibility of the RED
MOTION MOUNT Ti PL, see the MOTION MOUNT Operation Guide at www.red.com/downloads.
WARNING: Using a non-standard PL mount lens or device with a DSMC PL mount may damage the DSMC and
lens mount. Any damage caused by not using a standard PL mount lens or device will not be covered under
warranty.
173


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Red WEAPON - 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Red WEAPON - 2015 in the language / languages: English as an attachment in your email.

The manual is 9,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info