597828
172
Zoom out
Zoom in
Previous page
1/183
Next page
COPYRIGHT © 2015 RED.COM, INC
RED DSMC OPERATION GUIDE: WEAPON
955-0116_V6.1, REV-E | 172
REMOVE A LENS MOUNT
NOTE: You can change lens mounts in the field. However, RED
®
recommends that you change lens mounts only
in a dust-free environment.
REQUIRED TOOL: T20 TORX
®
driver
1. Turn off the DSMC.
2. Attach the DSMC to a stable platform or position the DSMC on a clean and level work surface so that the
lens mount screws are accessible.
3. Remove the lens and any DSMC modules, cables, or other accessories that might interfere with removing
the lens mount.
4. If removing the DSMC Mg PL Mount 2.0, turn the locking ring slightly counter-clockwise so that you can
acess the lens mount screws.
5. Loosen and remove the four (4) M4x0.7 x 8 mm lens mount screws in a cross pattern (“X” pattern) using a
T20 TORX driver.
NOTE: The DSMC Mg PL Mount 2.0 has captive screws that are not removable from the mount.
NOTE: Screw removal may require a large handle T20 TORX driver and additional leverage.
6. Remove the lens mount from the DSMC.
INSTALL A LENS MOUNT
NOTE: You can change lens mounts in the field. However, RED recommends that you change lens mounts only
in a dust-free environment.
REQUIRED TOOL: T20 TORX driver
1. Ensure that the DSMC is turned off and remove any accessories or cables that may interfere with installation.
2. Inspect the gold electrical contact pins on the front of the DSMC and the gold contact pads on the rear of
the lens mount to ensure that they are free of any contamination.
3. Align the lens mount on the front of the DSMC BRAIN. The DSMC connection pins must align with the lens
mount pins.
4. If installing the DSMC Mg PL Mount 2.0, turn the locking ring slightly counter-clockwise so that you can
acess the lens mount screws.
5. Replace and loosely tighten the four (4) M4x0.7 x 8 mm lens mount screws in a cross pattern (“X” pattern)
using a T20 TORX driver.
WARNING: DO NOT FULLY TIGHTEN.
NOTE: The DSMC Mg PL Mount 2.0 has captive screws that are not removable from the mount.
6. Tighten the four (4) lens mount screws evenly in a cross pattern (“X” pattern) using a T20 TORX driver. DO
NOT exceed 350 in-oz, or damage may occur.
WARNING: DO NOT OVERTIGHTEN.
7. After installation, a hardware rediscover or firmware upgrade may be required, particularly if you are installing
a MOTION MOUNT. If a MOTION MOUNT is not recognized, you will be unable to access the Motion Mount
menu at Menu > Settings > Setup > Lens.
To perform a hardware rediscover, go to Menu > Settings > Maintenance > Rediscover. A system reboot is
required after a hardware rediscover.
NOTE: If you need to replace any screws, please contact your Bomb Squad representative.
172


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Red WEAPON - 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Red WEAPON - 2015 in the language / languages: English as an attachment in your email.

The manual is 9,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info