558423
86
Zoom out
Zoom in
Previous page
1/460
Next page
5.2 Mounting - c Series and e Series
Removing the rear bezel
You must remove the rear bezel before surface
mounting the display.
Note: These steps do not apply to the e165 as it
does not require a rear bezel.
1. Remove the front bezel. Refer to the separate
instructions provided for that procedure.
D12184-3
e7 / e7D
1
3
2
2. Remove the screws that secure the bezel to the
display (only required for e7 and e7D).
3. Carefully remove the bezel from the rear of the
display, pulling the bezel gently along the:
i. Outer edges - work from the sides upwards
and then along the top edge, ensuring that the
clips are fully released from the display.
ii. Inner edges - ensure that the bezel is
completely removed from the display.
Note: Only the e7 and e7D have xing screws for
the rear bezel, other multifunction display variants
have clips which hold the rear bezel in place.
Surface mounting
The display can be surface mounted.
Before mounting the unit, ensure that you have:
Selected a suitable location.
Identied the cable connections and route that the
cables will take.
Detached the front bezel.
D12271-2
1. Check the selected location for the unit. A clear,
at area with suitable clearance behind the panel
is required.
2. Fix the appropriate cutting template supplied
with the product, to the selected location, using
masking or self-adhesive tape.
3. Using a suitable hole saw (the size is indicated
on the template), make a hole in each corner of
the cut-out area.
4. Using a suitable saw, cut along the inside edge
of the cut-out line.
5. Ensure that the unit ts into the removed area
and then le around the rough edge until smooth.
6. Drill 4 holes as indicated on the template to
accept the xings.
7. Place the gasket onto the display unit and press
rmly onto the ange.
8. Connect the power, data and other cables to the
unit.
9. Slide the unit into place and secure using the
xings provided.
Note: The supplied gasket provides a seal
between the unit and a suitably at and stiff
mounting surface or binnacle. The gasket should
be used in all installations. It may also be
necessary to use a marine-grade sealant if the
mounting surface or binnacle is not entirely at and
stiff or has a rough surface nish.
Attaching the rear bezel
The rear bezel must be tted if you wish to use a
mounting bracket to mount the unit.
Note: These steps do not apply to the e165 as it
does not require a rear bezel.
1. Remove the front bezel. Refer to the separate
instructions provided for that procedure.
2. Place the bezel over the rear of the display,
ensuring that it is correctly aligned with the
display. Apply rm but even pressure to the bezel
along the:
86 a Series / c Series / e Series
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Raymarine c Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Raymarine c Series in the language / languages: English as an attachment in your email.

The manual is 30,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Raymarine c Series

Raymarine c Series User Manual - German - 396 pages

Raymarine c Series User Manual - Dutch - 394 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info