500597

Radson 51055 - SLAVE RF Manual

5
Zoom out
Zoom in
Previous page
1/40
Next page
5
4. SMALL DESCRIPTION
This controller (Receiver + Master) with the main zone programmer are a complete package to manage all
component of your water floor heating and cooling installation.
You could control different type of installations:
Installation1: Heating only.
Installation2: Cooling Only
Installation3: Separate systems (Boiler and water chillers) or slave heat pump.
Installation4: Reversible Heat pump (manual or automatic)
Installation5: Reversible Heat pump (without Heat & Cool information and control)
In case of cooling function is used, you could control the residual humidity in the house by:
The special input on the receiver which can be use for a NTC or Humidity sensor mounting on incoming pipe of
the manifold or a special humidity sensor (see the wiring diagram).
5. LED EXPLANATION
Keyboards:
Validation key (OK)
Plus key (+)
Minus key (-)
Navigation key left (◄)
Navigation key right (►)
Display:
Humidity drier output activated.
1. Comfort mode indicator.
2. Reduced mode indicator.
3. Anti-freeze mode indicator.
4. Heating mode indicator (blinks when operating).
5. Cooling mode indicator (blinks when operating).
6. Room temperatures indicator.
7. Current zone or Room temperature if 7 displayed.
8. Radio frequency graphic.
9. Setting temperature required by the zone thermostat
Or floor temperature if floor sensor is used and 7 displayed.
Special displaying:
FL.l: Indicate that the zone thermostat is in « Floor Lower limitation mode »
FL.h: Indicate that the zone thermostat is in « Floor upper limitation mode »
(Only available if floor sensor is connected)
OFF: Indicate that the thermostat is stopped.
LED 1: Red => Heating demand indication
Red blinking => Heat & cool sensor error
Green => Cooling demand indication
Green Blinking => Humidity detection (Humidity drier is activated)
Off => System in standby
LED 2: Orange => Pump running indicator
LED 3 to 6 (or Led 14 with 2 slaves):
Green Flash: => indicates a correct radio reception on zone.
Green blinking: => - In normal functioning if you press one key indicates the current zone or group zone
selected.
Red: =>Indicates that the zone is activated (Water circulation on this circuit)
Red blinking: Indicates that this zone is in radio reception alarm. The RF thermostat radio signal has
been lost.
(See Radio reception alarm section).
LED1 ------------------------------------------------------------------ LED14
8
4
2
6
1
10
7
5
3
9
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Radson 51055 - SLAVE RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Radson 51055 - SLAVE RF in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info