713892
18
Zoom out
Zoom in
Previous page
1/188
Next page
ENGLISH
18 HeliX
2
Options – Hemiplegic armrests
HEMIPLEGIC ARMRESTS
The hemiplegic armrest can be
adjusted both in length and
angle. You can adjust the
length by pushing the armrest
after having loosened the 2
rotary screws (1). To adjust the
angle, hold the knob 2 pushed
down and rotate the armrest to
the desired position, then
release the knob again.
(Fig. 42).
Fig. 42
ANTI-TIP TUBES
Anti-tip tubes provide additional safety for inexperienced users
when they are still learning how to operate their wheelchair. They
prevent a wheelchair from tipping over backwards. The anti tip tube
should be inserted into the frame tube until the first of the two
spring buttons enters the first hole in the frame tube, (Fig.40).
WARNING!
Incorrect setup of the anti-tips will increase the risk of a rearwards
tip. You must swing the anti-tips upwards when going up or down
large obstacles, (such as a kerb), to prevent them from touching the
ground, then rotate them back down to the normal position.
CAUTION!
Do not insert both buttons of
the anti tip tube into the frame
tube as this could damage the
anti Tip and cause a loss of
effectiveness.
By pushing on the Second
exposed release button, the
safety wheels can be set
upwards or removed. There
must always be a gap of
between 3 cm and 5 cm
between the tube and the
ground. You must swing the
safety wheels upwards when going up and down large obstacles
(such as a kerb) to prevent them from touching the ground. Then
rotate the safety wheels back down to the normal position (Fig. 43).
WARNING!
Incorrect set up of the anti tips will increase the risk of a rearwards
tip.
Options – Anti-Tip Tubes
Fig. 43
WARNING!
Before using your wheelchair ensure the seat belt is worn and
correctly adjusted before use.
The lap belt is fitted to the wheelchair as shown in the illustrations.
The seat belt comprises 2 halves. They are fitted using the existing
seat stay retaining bolt fitted through the eyelet on the belt. The belt
is routed under the rear of the side panel. (Fig. 44)
Adjust the belt position so buckles are in the centre of the seat,
(Fig. 45).
Options – Lap belt
Adjust lap belt to suit the users needs as follows:
To increase the belt
length
To reduce the belt
length
Feed free belt
through slide adjust-
ers and male buckle
to provide more belt
length.
Feed free belt back
through male buckle
and slide adjusters.
Ensure belt is not
looped at male
buckle.
When fastened check space between the lap belt and user, when
correctly adjusted it should not be possible to insert more than the
flat of the hand between the lap belt and the user, (Fig. 46).
Generally the Lap Belt should be fixed so that the straps sit at an
angle of approximately 45°, and when correctly adjusted should not
allow user to slip down in the seat,
(Fig. 47).
Fig. 44
Fig. 45
Type A
Type AType A
Type B
Type B
Type B
Fig. 46
Fig. 47
To fasten buckle:
Firmly push male buckle into
female buckle.
To release belt:
Press exposed sides of male
buckle and push towards centre
/ push the press button of the
female buckle whilst gently pull-
ing apart.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quickie RubiX 2 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quickie RubiX 2 Plus in the language / languages: English, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info