Manual Quickie HeliX 2 Comfort (page 18 of 188) (English, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish)

713891

Zoom out

Zoom in

1/188

ENGLISH

18 HeliX

Options – Hemiplegic armrests

HEMIPLEGIC ARMRESTS

The hemiplegic armrest can be

adjusted both in length and

angle. You can adjust the

length by pushing the armrest

after having loosened the 2

rotary screws (1). To adjust the

angle, hold the knob 2 pushed

down and rotate the armrest to

the desired position, then

release the knob again.

(Fig. 42).

Fig. 42

ANTI-TIP TUBES

Anti-tip tubes provide additional safety for inexperienced users

when they are still learning how to operate their wheelchair. They

prevent a wheelchair from tipping over backwards. The anti tip tube

should be inserted into the frame tube until the first of the two

spring buttons enters the first hole in the frame tube, (Fig.40).

WARNING!

Incorrect setup of the anti-tips will increase the risk of a rearwards

tip. You must swing the anti-tips upwards when going up or down

large obstacles, (such as a kerb), to prevent them from touching the

ground, then rotate them back down to the normal position.

CAUTION!

Do not insert both buttons of

the anti tip tube into the frame

tube as this could damage the

anti Tip and cause a loss of

effectiveness.

By pushing on the Second

exposed release button, the

safety wheels can be set

upwards or removed. There

must always be a gap of

between 3 cm and 5 cm

between the tube and the

ground. You must swing the

safety wheels upwards when going up and down large obstacles

(such as a kerb) to prevent them from touching the ground. Then

rotate the safety wheels back down to the normal position (Fig. 43).

WARNING!

Incorrect set up of the anti tips will increase the risk of a rearwards

tip.

Options – Anti-Tip Tubes

Fig. 43

WARNING!

Before using your wheelchair ensure the seat belt is worn and

correctly adjusted before use.

The lap belt is fitted to the wheelchair as shown in the illustrations.

The seat belt comprises 2 halves. They are fitted using the existing

seat stay retaining bolt fitted through the eyelet on the belt. The belt

is routed under the rear of the side panel. (Fig. 44)

Adjust the belt position so buckles are in the centre of the seat,

(Fig. 45).

Options – Lap belt

Adjust lap belt to suit the user’s needs as follows:

To increase the belt

length

To reduce the belt

length

Feed free belt

through slide adjust-

ers and male buckle

to provide more belt

length.

Feed free belt back

through male buckle

and slide adjusters.

Ensure belt is not

looped at male

buckle.

When fastened check space between the lap belt and user, when

correctly adjusted it should not be possible to insert more than the

flat of the hand between the lap belt and the user, (Fig. 46).

Generally the Lap Belt should be fixed so that the straps sit at an

angle of approximately 45°, and when correctly adjusted should not

allow user to slip down in the seat,

(Fig. 47).

Fig. 44

Fig. 45

Type A

Type AType A

Type B

Fig. 46

Fig. 47

To fasten buckle:

Firmly push male buckle into

female buckle.

To release belt:

Press exposed sides of male

buckle and push towards centre

/ push the press button of the

female buckle whilst gently pull-

ing apart.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Quickie HeliX 2 Comfort in the language / languages: English, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Quickie HeliX 2 Comfort Manual

Product: