Manual Quickie Argon 2 (page 16 of 72) (English, Dutch, French)

713882

Zoom out

Zoom in

1/72

ENGLISH

Argon

Rev.1.0

Seat

Seat Sling

Remove the screws on the left

side of the sling. Adjust the

VELCRO® material to increase

the tension of the seat sling.

Tighten up the screws again.

If the screws are difficult to fit

back in place, try and locate the

holes with a sharp object.

Ensure also that the plastic base is in the correct position

before the screws are tightened again, (Fig.4.16).

Fig.4.16

Seat height

Adjusting the Seat Height (Fig.4.17)

To adjust rear seat height, slacken and remove the 4

screws (1) (2 each side), which

secures the clamp (2) Adjust the two clamps to the

required height and replace the 4 screws. Before

tightening the screws, please follow the instructions for

setting the toe-in/toe-out to zero (See Fig.4.19-4.20).

Tighten the screws to 7 Nm.

NOTE: An adjustment to the castor angle may be

necessary when adjusting the rear seat height.

Castor, Castor Adapter, Castor Fork

From time to time the wheelchair may veer slightly to the

right or left, or the castors may flutter. This may be caused

by the following:

• The forward or reverse wheel motion has not been set

properly.

• The castor angle has not been adjusted properly.

• Castor and/or rear wheel air pressure is incorrect;

wheels do not turn smoothly.

The optimum adjustment of the castors is required for the

wheelchair to run in a straight line.

Castors should always be adjusted by an authorized

dealer. The castor plates must be re-adjusted, and the

wheel locks must be checked any time the rear wheel

position has been altered.

Castors

Adjusting the Castor

To ensure that both forks are set parallel, simply count the

teeth visible on both sides. After setting the castor fork,

the teeth will guarantee a secure position, allowing an

adjustment of 16° in 2° increments. Use the flat side on

the front of the castor fork to check for a right-angled

position to the ground (Fig. 4.19).

The patented design allows the castor fork to be turned,

so that it can be reset at right-angles to the ground when

the seat angle is changed.

Setting the Directional Stability

Release the Allen screws (1) on the underside of the fork.

You can then undo the screw (2). You can now turn the

black socket (3) left or right.

Left – chair pulls to the left

Right – chair pulls to the right

Then tighten up the screw (2) again. Please set a 90°

angle from the fork to the floor.

Now tighten up the screw (1) again. (Fig. 4.20).

Fig. 4.19

+8 -8

Fig. 4.20

Fig.4.17

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Quickie Argon 2 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 1,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Quickie Argon 2 Manual

Product: