815530

Quadra-Fire Outfitter I - Pellet Manual

11
Zoom out
Zoom in
Previous page
1/30
Next page
11 10/238106-804K
B. Priming the Feed Tube
The feed tube may need to be primed only if the hopper
isbeing lled for the rst time or ifthe appliancehasrun
out of pellets. To prime the appliance, turn the dial control
QUICKLYfromtheOFFpositiontotheHIposition,toOFF
toHIinoneuidmotion.TheLEDlightwillbeasolidgreen
color to indicate a successful prime function. When the feed
motor is running continuously, the LED light will be a solid
greencolor.Whenpelletsstarttodropintotherepot,the
feed tube is primed. Turn the dial control to the desired
position and the appliance will begin its ignition sequence
with a blinking green light. Allow the appliance up to 20
minutes for ignition to occur.
When attempting Prime function it is NECESSARY
to operate the dial control QUICKLY in a single uid
motion. If this is not performed properly, the appliance
will not prime.
STOP!
Please Read Prior to Attempting Prime
Function
A FIREPOT THAT IS MORE THAN HALF FULL IS
OVERFILLED AND CAN BE DANGEROUS. DO NOT
OVERFILLFIREPOTFORIGNITION.
Overlling the repot could cause an unsafe ignition
resulting in injury or damage. Firepot must be emptied.
WARNING
!
MAXIMUM
PELLET LEVEL
Do not restart or manually add pellets or any type of fuel
to the burn pot during this process.
CAUTION
!
Iftheappliancedoesnotignite,theLEDlightwillblinkredfour
times showing a missed ignition alarm. Turn the appliance to
o󰀨andremoveandEMPTYtherepot.
Returntherepottotheapplianceinthecorrectorientation.
SeegureinCleaningFirepotintheGeneralMaintenance
sectionofOwner’sManualunderMaintainingandServicing
the Appliance.
Attemptrelightingsequence(seeLightingInstructionsGuide).
C. Firepot Burn Down
Afeatureofthesepelletappliancesistherepotburndown
cycle. The frequency of the cycle is once every hour the
appliance is burning. During this event, the feed is reduced
to the lowest setting and the exhaust blower ramps up to the
highest setting. The purpose of the burn down cycle is to help
removedebrisfromtherepotandhelptheapplianceburn
ase󰀩cientaspossible.Thecyclelasts99seconds.Please
be aware that the burn down does not replace daily cleaning
activities but makes them easier.
D. Shutdown
To shut the appliance down, turn the dial control counter
clockwisetotheOFFposition.Duringtheshutdownprocess,
theLEDwillashamberorgreenrapidlyjustliketheignition
sequence.Therepotburndowncyclewillbeginbutwithout
the feed motor running. The feed will be terminated during
this shutdown process. The exhaust and convection blowers
will remain on during the shutdown process until the exhaust
has cooled.
If maintenance or daily cleaning is going to be conducted
immediately following a shutdown, please use caution as
components especially those inside the rebox may still
be hot.
Please note that if the dial control is turned to the o󰀨
position and back on even if by mistake, the appliance
will go through the shutdown sequence.
E. Starting Your First Fire
1. Turnthedialcontrolto“OFF”.
2. Makesuretherepotisclean,inplace,andfreeofdebris.
3. Plug the appliance into the wall and ll the hopper with
wood pellets. Shut the hopper lid.
4. Turn the dial control to the desired burn setting.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Outfitter I - Pellet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Outfitter I - Pellet in the language / languages: English as an attachment in your email.

The manual is 4.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Outfitter I - Pellet

Quadra-Fire Outfitter I - Pellet User Manual - French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info