815530

Quadra-Fire Outfitter I - Pellet Manual

12
Zoom out
Zoom in
Previous page
1/30
Next page
12 10/238106-804K
The appliance will go into the ignition sequence followed
by start up (The green LED will ash rapidly). The ignition
sequence involves the exhaust blower turning on, the igniter
turning on, and the feed motor running in two stages. The
rststageinvolvesthe feed motorrunningcontinuouslyfor
aboutaminutetopreloadpelletsintotherepot.Following
the preload and a delay, the feed motor will begin cycling on
ando󰀨.Whenthepelletsarewarmingupandonthevergeof
igniting,itisnotuncommonforthereboxtollwithsmoke.
Onceignitionactuallyhappens,thesmokeshouldevacuate
quickly. During this stage as well as any part during the burn
process, the front door should not be opened. This cycle
continues until the appliance senses ignition by a rise in the
exhaust temperature or the appliance times out. Following
the ignition cycle the appliance begins to feed additional
pelletsgraduallyforafewminutestobuildupthere.Thisis
important to have a controlled start up to keep the appliance
in balance.
F. Fire Characteristics
The overall height of the ame will vary throughout the
burnforacoupleofreasons.Theamewillvarybasedon
type of fuel or even batch of fuel. The second characteristic
that a󰀨ects the re relates to general maintenance and
cleaning.Infrequentorpoorgeneralmaintenancewillresult
ispoorerperformance.Indicatorsoftheneedforadditional
maintenance activities include a lazy ame, black sooted
glass, pellets not igniting, or pellets falling to the side of
the repot. See the maintenance section for additional
information.
G. Ignition Cycles
1. At the beginning of each ignition cycle, it is normal to see
somesmokeintherebox.Thesmokewillstoponcethe
restarts.
2. The convection blower will automatically turn on after
your appliance has reachedasu󰀩cienttemperature.
3. This blower transfers heat from your appliance into the
room, and will continue to run even after the appliance
hasshutdown.Itwillturno󰀨aftertheexhausttemperature
has cooled.
4. Occasionallytheappliance may run out of fuel and shut
itself down. When this happens the empty hopper alarm
will be triggered.
H. Trim Adjustment
Trim adjustment is the small dial located below the main
dial control. The function of the trim adjustment is to allow for
variationsinelevation,ventingandinstallationcongurations,
and fuel types (hard wood/soft wood).
Odors, vapors, and smoke released during
initial operation.
• Curing of high temperature paint.
• Openwindowsforaircirculation.
Odorsmaybeirritatingtosensitiveindividuals.
CAUTION
!
Figure 12.1
I. Clear Space
NOTICE: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction.
Mantel: Avoid placing candles and other heat-sensitive
objects on mantel or hearth. Heat may damage these objects.
RISK OF FIRE!
DoNOTplacecombustibleobjectsinfrontortothesides
of the appliance. High temperatures may ignite clothing,
furniture or draperies.
WARNING
!
RISK OF FIRE!
Keep combustible materials, gasoline and other
ammablevaporsandliquidsclearofappliance.
• Do NOT store ammable materials in the
appliance’s vicinity.
• DoNOTusegasoline,lanternfuel,kerosene,charcoal
lighteruidorsimilarliquidstostartor“freshenup”a
reinthisheater.
Keep all such liquids well away from the heater while it is
in use as combustible materials may ignite.
WARNING
!
Rotatingthisdialwilladjusttheair/fuelratiototheappliance:
• Clockwiseadjustmentsincreasetheameheight.
• Counter-clockwise adjustments will decrease the ame
height.
• When changing trim settings only adjust 1 level at a time,
allowing 15 minutes for re to stabilize before making
another adjustment. It may be necessary for an event to
happenbeforeanadjustmenttakese󰀨ect.Toensurethe
trim adjustment takes e󰀨ect, change the dial control to a
di󰀨erentburnrate.Afterthestovehasadjustedtothenew
burn rate, rotate the dial back to the desired setting.
• The factory default trim adjustments are set to zero (0) for
mostfuelsandrecommendedventingcongurations.
Aproperlyadjustedrewillhaveabright,activeamepattern
that extends out of the re pot approximately 6 to 9 inches
whenburningonhigh.Aproperlyadjustedrewillburncleaner
andhavehighere󰀩ciencies.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Outfitter I - Pellet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Outfitter I - Pellet in the language / languages: English as an attachment in your email.

The manual is 4.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Outfitter I - Pellet

Quadra-Fire Outfitter I - Pellet User Manual - French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info