815525
27
Zoom out
Zoom in
Previous page
1/40
Next page
27 04/217027-805J
B. Ba󰀪e
PART NUMBERS:
LEFT BAFFLE: 812-4200
RIGHT BAFFLE: 812-4210
1. Use proper shut down procedures to shut down the
appliance and let it completely cool down.
2. Open right side panel and then open the door.
3. The 2 ba󰀪es are located at the top inside of rebox.
4. Place your hand on the ba󰀪e and slide it up and the
bottom edge will fall down and then you can lift the ba󰀪e
out. Repeat for the other side.
a. Remove Ba󰀪e to Access Heat Exchanger Tubes
and Firebox Exhaust Exits
i. Open the upper right side panel door and then
open the glass door.
ii. The 2 ba󰀪es are located at the top inside of rebox.
iii. Place your hand on the ba󰀪e and slide it up and
the bottom edge will fall down and then you can lift
the ba󰀪e out. Repeat for the other side.
iv. Re-install in reverse order.
C. Igniter
PART NUMBER: SRV7000-462
1. Be sure the appliance is allowed to cool, has been
unplugged and the exhaust blower is o󰀨. Remove the
ash pan.
2. The wire leads to the igniter are connected to the wire
harness with 1/4 inch male / female spade connectors.
These wires will pull forward approximately 4 to 5 inches
(102mm to 127mm). Disconnect the spade connections
and remove the igniter from the chamber. Loosen the
thumb screw and slide igniter out (Figure 27.1).
3. Install new igniter into the chamber and tighten the
thumb screw. Re-connect the wires to the 2 leads with
the spade connectors.
4. Push excess wire leads to take-up the 4 to 5 inches
(102mm to 107mm) previously pulled out. This will keep
the wires out of the way of the ash pan. Double check
that the igniter wires are clear of any movement, i.e. ash
pan, re pot cleaning rod, etc.
5. Re-install the ash pan and re-connect the power.
Figure 27.1
Igniter
Igniter Bracket
Thumb Screw
Shock Risk.
Do NOT remove grounding prong
from plug.
Plug directly into properly grounded 3
prong receptacle.
Route cord away from appliance.
Do NOT route cord under or in front
of appliance.
CAUTION
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Classic Bay 1200 - Pellet - Insert at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Classic Bay 1200 - Pellet - Insert in the language / languages: English as an attachment in your email.

The manual is 9.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Classic Bay 1200 - Pellet - Insert

Quadra-Fire Classic Bay 1200 - Pellet - Insert User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info