815528
10
Zoom out
Zoom in
Previous page
1/40
Next page
10 02/237022-802K
G. General Operating Information
1. Thermostat Calls For Heat: The appliance is like most
modern furnaces; when the thermostat calls for heat,
your appliance will automatically light and deliver heat.
When the room is up to temperature and the thermostat is
satised, the red call light will shut off and the appliance
will shut down. The red call light is located behind the
right access panel.
2. Heat Output Controls: This appliance is equipped with
a heat output control switch that has three settings or
burn rates; low, medium and high (Figure 10.1). The
appliance will turn on and off as the thermostat demands.
When the thermostat calls for heat, the appliance will
always start up on High. After burning approximately
4 minutes, the appliance will then burn at the rate at
which it was originally set. If the appliance is set at one
of the lower settings, it will run quieter but takes longer
to heat up an area than if it were set at a higher burn
rate. Regardless of the burn rate, when the area is warm
enough to satisfy the thermostat, the appliance will shut
off.
H. Starting Your First Fire
1. A thermostat is required for proper operation of this
appliance. At this time, ll the hopper with pellets, set the
thermostat to its lowest setting. Plug the power cord into
nearby outlet.
2. The exhaust blower will stay on for approximately 18
minutes even though the thermostat is not calling for
heat. This is normal.
3. Locate the heat output control switch on the lower right
side of the rebox behind decorative front door. Set to the
HIGH setting and then adjust the thermostat to its highest
setting. The red call light will be on which is located on the
top of the junction box behind the right access panel. This
indicates the thermostat is calling for heat (Figure 10.1).
4. The fuel feed system and the igniter should
now
be on.
5. For your rst re it will be necessary to press the reset
button once per minute until pellets start to drop into the
re pot, then press button 1 more time. This will ll the
feed system and allow the appliance to begin dropping
pellets. The appliance will continue to run as long as the
thermostat is calling for heat.
6. Once the appliance has ignited, let it burn for approximately
15 minutes, then set the thermostat to the desired room
temperature. Adjust the heat output control switch to the
desired setting.
Figure 10.1
High
Med
Low
Reset
Button
WARNING
Fire Hazard.
Keep combustible materials, gasoline and
other ammable vapors and liquids clear of
appliance.
Do NOT store ammable materials in the
appliance’s vicinity.
NEVER use gasoline, GASOLINE-TYPE lantern fuel,
kerosene, charcoal lighter uid, or similar liquids to
start or “freshen up” a re in this appliance. Keep all
such liquids well away from the appliance while it is
in use.
DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS
SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL.
DO NOT USE CHEMICALS OF FLUIDS TO START
THE FIRE.
Combustible materials may ignite.
WARNING
Fire Risk
Do NOT operate appliance:
With appliance door open.
Fire pot oor open.
Cleaning slide plates open.
Do NOT store fuel:
Closer than required clearances to combustibles to
appliance
Within space required for loading or ash removal.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Castile - Pellet - Insert at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Castile - Pellet - Insert in the language / languages: English as an attachment in your email.

The manual is 9.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Castile - Pellet - Insert

Quadra-Fire Castile - Pellet - Insert User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info