633111
51
Zoom out
Zoom in
Previous page
1/176
Next page
51
4
51
D OPERATION WITH REMOTE CONTROL
G
NOTE!
Always aim the remote controller towards the receiver on the indoor unit and make sure there
are no obstacles in between the remote control and the receiver on the indoor unit. Otherwise
the remote control signal will not be picked up by the receiver and the air conditioner will not
work properly.
The maximum distance at which the remote control will work is approximately 6 to 7 meters.
G
NOTE!
Keep the remote controller where its signal can reach the receiver of the unit. When you select
the timer operation, the remote controller automatically transmits a signal to the indoor unit
at the specified time. If you keep the remote controller in a position that hinders proper signal
transmissions, a time lag of up to 15 minutes may occur.
Introduction of Function Buttons on the Remote Controller
1
2
8
6
7
4
15
3
12
11
5
9
10
14
13
a On/off Button: Push this button to start the unit operation. Push the button again to stop the unit
operation.
b Mode Button: Each time you press the button, a mode is selected in a sequence that goes from AUTO
COOL DRY HEAT and FAN only as the following figure indicates:
AUTO COOL DRY HEAT FAN
c + Button: Push the button to increase the indoor temperature setting to 30ºC.
d - Button: Push the button to decrease the indoor temperature setting to 17ºC.
e Fan Button: This button is used for selecting Fan Speed. Each time you press the button, a fan speed is
selected in a sequence that goes from AUTO, LOW, MED to HIGH, then back to Auto. When you select the
AUTO or DRY mode, the fan speed will be automatically controlled and you can not set the fan speed.
f SLEEP Button: Press this button to go into the Energy-Saving operation mode. Press it again to cancel.
This function can only be used on COOL, HEAT and AUTO mode and maintain the most comfortable
temperature for you. The unit automatically increases the set temperature by 1ºC per hour (in cooling
mode) or decreases the set temperature by 1ºC per hour (heating mode) during the first 2 hours. The air
conditioner will maintain this temperature (set temperature – or + 2 degrees) during the next 5 hours.
After this period, the air conditioner will shut itself down.
g Swing Button: Press the SWING button to activate the swing feature. Push the button again to stop.
fig. 1
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Qlima - Zibro S3364 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Qlima - Zibro S3364 in the language / languages: English, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian as an attachment in your email.

The manual is 5,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info