782208

Proxxon MICROMOT Motorized Carver MOS Manual

6
Zoom out
Zoom in
Previous page
1/10
Next page
- 6-
Table 1
Minimum gage for cord
Effective date for Table 1 changed from November 1, 1995 to
November 11, 1996
Ampere Rating Volts Total length of cord in feet
120 V 25 ft. 50 ft. 100 ft. 150 ft.
More Not More AWG
Than Than
06 18 16 16 14
General view (Fig. 1):
1. On / Off switch
2. Speed control knob
3. Scale for Z direction (moveable)
4. Spindle cover
5. KT 70 work table (210 mm x 70 mm)
6. Support
7. Hole for securing base
8. Adjusting screws
9. Clamping set
10. Clamp screw
11. Table for spindle speeds
12. Collet chucks
13. Handwheel for X direction
14. Scale ring for X direction
15. Handwheel for Y direction
16. Scale ring for Y direction
17. Handwheel for Z direction
18. Scale ring for Z direction
19. Moving scale for X direction
20. Base plate
21. Cover
22. Spanners
Description of the machine
The PROXXON MF 70 MICRO Milling Machine is the
ideal machine for all fine and precision milling work for
metals (cast iron, steel, brass, aluminium), plastics or
wood. With the high spindle speed of 5,000 to 20,000
rpm (enabling the use of the smallest milling cutter
diameters) in conjunction with the high-precision KT 70
microcoordinate table, all pre-conditions for precise
and clean operation are fulfilled.
The basic equipment includes:
– Milling spindle with Z-pillar and stable base
– Collet chuck block with collet chucks
– (Ø 1.0; 1.5; 2.0, 2.4; 3.0 and 3.2 mm)
– KT 70 microcoordinate table, complete
– Clamping set
– Several fastening materials
(not illustrated, see exploded drawing)
– Fastening screws for KT 70 micro coordinate table
– Auxiliary tools
– Operating instructions and safety regulations
Technical data
Voltage: ~115 Volts, 60 Hz
Power rating: 0.9 A
No-load spindle speed (no) 5.000 – 20.000 rpm
Vertical adjustment travel
(z-direction) 3 10/64” (80 mm)
Lateral adjustment travel (x-direction) 5
17/64
” (134 mm)
Longitudinal adjustment travel
(y-direction) 1 13/16” (64 mm)
Table size: 7 7/8“ x 2 3/4” (200 x 70 mm)
Scale rings: 1 turn = 0,04” (1 mm)
1 graduation line = 2/1000” (0,05 mm)
Dimensions of T-grooves: 15/32” x 15/64” x 15/64”
(12 x 6 x 6 mm, MICROMOT-norm)
Spacing of T-grooves: 1” (25 mm)
Size of base: 5 7/64” x 8 55/64” (130 x 225 mm)
Overall height: 13 25/64” (340 mm)
Weight approx. 15.5 lb (7 kg)
Noise emission: ≤ 70 dB(A)
Vibration ≤ 2.5 m/s2
Assembly of the milling machine
Warning:
To avoid injury from unexpected starting or electrical
shock, do not plug the power cord into a power source
receptacle during unpacking and assembly. This cord
must remain unplugged whenever you are working on
the milling machine.
– Attach the compound-type table 1(Fig. 2) to the
base 2with the 4 x M4 Allen screws supplied.
– The milling machine must now be fastened to a
stable work surface with 4screws 3.
Operation
Installation of the collet chucks
Important:
Disconnect the mains plug before changing tools.
Tightening the union nut without a suitable shank
inserted, damages the collet chuck.
1. Block the spindle with a spanner and release union
nut 1(Fig. 3).
2. Insert the required collet chuck 2using suitable
inserting tool 3.
3. Block milling spindle and re-tighten union nut.
Note:
All inserting tools must be tightened with as little
protrusion as possible. Excessively protruding shanks
vibrate and cause poor milling results.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon MICROMOT Motorized Carver MOS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon MICROMOT Motorized Carver MOS in the language / languages: English as an attachment in your email.

The manual is 0.68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info