Manual Proxxon MICROMOT Motorized Carver MOS (page 5 of 10) (English)

782208

Zoom out

Zoom in

1/10

- 5-

Additional safety instructions :

This milling machine is for indoor use only. Do not

expose to rain or use in damp locations.

Use only accessories recommended for this milling ma -

chine. Follow the instructions that accompany

accessories. Use of improper accessories may cause

hazards.

Do not attempt to modify this tool or create

accessories not recommended for use with this tool.

Any such alternation or modification is misuse and

could result in hazardous condition leading to possible

serious injury.

To avoid injury from unexpected starting or electrical

shock, do not plug the power cord into a power source

receptacle during unpacking and assembly. This cord

must remain unplugged whenever you are working on

the milling machine.

If any part is missing or damaged, do not plug the

milling machine in until the missing or damaged part is

replaced, and assembly is complete. To avoid electrical

shock, use only identical replacement parts when

servicing grounded tools.

For your safety, never connect the plug to the power

source receptacle until the assembly and adjustment

steps are completed, and you have read and

understood the safety and operating instructions.

To avoid injury from accidental start, make sure the

switch is in the OFF position and the plug is not

connected to the power source receptacle before

changing any parts or tools (i. e. miller)

To avoid injury from accidental start, make sure the

switch is in the OFF position and the plug is not

connected to the power source receptacle before

making any adjustments.

For your own safety, do not plug the tool into the

power source receptacle or insert the switch key, until

the parts are correctly installed and adjustments have

been made.

For your own safety, use only millers sized and

recommen ded for this milling machine. Follow the

instructions that accompany the millers.

To avoid fire or toxic reaction, never use gasoline,

naphtha, acetone, lacquer thinner, or similar highly

volatile solvents to clean the milling machine.

Do not allow brake fluids, gasoline, or penetrating oils

to come in contact with the plastic parts. They contain

chemicals that can damage or destroy plastics.

Only qualified service technicians should do all

electrical or mechanical repairs.

When servicing use only PROXXON replacement parts.

Use of any other parts may create a hazard or cause

product damage.

Any attempt to repair or replace electrical parts on this

lathe may create a hazard unless repair is done by a

qualified service technician. Repair service is available

at your PROXXON service center (You find the address

at the back of this manual)

GROUNDING INSTRUCTIONS:

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current

to reduce the risk of electric shock. This tool is

equipped with an electric cord having an equipment-

grounding conductor and a grounding plug. The plug

must be plugged into a matching outlet that is properly

installed and grounded in accordance with all local

codes and ordinances. Do not modify the plug

provided -- if it will not fit the outlet, have the proper

outlet installed by a qualified electrician.

Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. The

conductor with insulation having an outer surface that

is green with or without yellow stripes is the

equipment- grounding conductor. If repair or

replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to

a live terminal. Check with a qualified electrician or

service personnel

if the grounding instructions are not completely under -

stood, or if in doubt as to whether the tool is properly

grounded.

Use only 3-wire extension cords that have 3prong

grounding plugs and 3pole receptacles that accept the

tool's plug.

Repair or replace damaged or worn cord immediately.

This tool is intended for use on a circuit that has an

outlet that looks like the one illustrated in Sketch A in

Figure 28. The tool has a grounding plug that looks like

the plug illustrated in Sketch A in Figure 8. A temporary

adapter, which looks like the adapter illustrated in

Sketches B and C, may be used to connect this plug to

a 2-pole receptacle as shown in Sketch B if a properly

grounded outlet is not available. The temporary adapter

should be used only until a properly grounded outlet

can be installed by a qualified electrician. The green-

colored rigid ear, lug, and the like, extending from the

adapter must be connected to a permanent ground

such as a properly grounded outlet box.

Grounding methods

<B>

GROUNDING

ADAPTER

GROUNDING

MEANS

METAL SCREW

COVER OF GROUNDED

OUTLET BOX

<A> <B>

<C>

<D>

Fig. 8

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon MICROMOT Motorized Carver MOS in the language / languages: English as an attachment in your email.

The manual is 0.68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Proxxon MICROMOT Motorized Carver MOS Manual

Product: