782198
11
Zoom out
Zoom in
Previous page
1/20
Next page
- 11 -
The replacement saw blades are stored in the “saw blade
garage" 3, on the side of the panelling of the top arm.
The DSH/E saws soft wood up to a thickness of 2", plastic up
to 1 1/4" and non-ferrous metals up to 0.4".
The saw can also be used without problem for separating
Plexiglas, GRP, foam, rubber, leather and cork.
And so that the dust does not obscure the view of the cutting
line when working, there are automatically driven bellows with
adjustable air nozzle 7. An additional vacuum cleaner can also
be connected. The connecting piece 11 is positioned at 90° to
save space.
This guarantees clean work.
Scope of supply:
1 pc. Scroll Saw DSH/E
1 pc. connector for Vacuum cleaner
1 pc. Bag with air nozzle incl. accessories
5 pc. Saw blades 18 teeth
5 pc. Saw blades 25 teeth
1 pc. Allen key with T-handle
1 pc. Operating manual
7 Technical data
No. of strokes: 400-1.600 strokes per min.
Stroke height: 3/4"
Max. cutting
height (90°): 2"
Max. cutting
height (45°): 1"
Table tilt: 0-45°
Cutting blade length: 5" Pin-Type or Plain End (without
cross pin)
Net weight: 34.6 lb
Dimensions:
LxWxH
20 7/8" x 10 5/8" x 11 13/16"
Table: 14 1/8" x 10 5/8"
Depth of Throat: 15 3/4"
Motor:
Voltage: 110-120 V, 60 Hz
Amps: 1.6 A
8 Set-up and commissioning of the saw:
CAUTION:
For your own safety, do not operate your Scroll Saw until it is
completely assembled and installed according to the following
instructions!
Disconnect power to the machine during the entire assembly
process. Failure to do this may result in serious personal
injury.
8.1 Unpacking (fig. 1a and 1b):
Disconnect power to the machine during the entire assembly
process. Failure to do this may result in serious personal
injury.
1. Unpack the device and remove it from the box. Ensure that
the device is not lifted by the plastic panelling around the
top arm 4 (as shown on the sheet attached to the
packaging).
2. For transport reasons, the saw table is tilted up at an angle
of about 45°. Turn the toggle 10 to tilt the table back into
the horizontal position (the precise setting is described
below). Then thighten the toggle 10 again.
8.2 Attaching Blade Guard
Your DSH/E Scroll Saw is provided with the attached blade
guard. But for some of the actions and adjustments described
in this manual it could be necessary to detach the blade
guard.
Attaching and detaching the blade guard:
1. Bend up the saw blade guard on the upper side and hang it
out like shown in illustration 2a.
2. For attaching the saw blade guard just act the opposite
way around: Bend up the saw blade guard on the upper
side and hang it in. There are holes in the upper cover
designed for that.
8.3 Setting up the saw:
NOTE:
Safe and precise work is only possible with careful fixing!
Bolt your Scroll Sas securely to a stand or workbench. If there
is any tendency for the Scroll Saw to tip over or move during
certain operations (for example cutting long, heavy boards),
fix the Scroll Saw stand or the workbench to the floor.
1. Secure saw with two screws (not included in scope of
delivery) on a solid workbench. Use the drill holes intended
for this purpose (17, fig. 1) which are located at the front
and back of the saw base.
The saw is equipped with rubber feet for noise insulation. If
required, you can also place an additional plastic or cork
underlay between the machine and the standing surface (not
included in scope of delivery!).
Proxxon_BedienAnl_DSH_US_Bel 10.06.2005 14:20 Uhr Seite 11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon DSH-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon DSH-E in the language / languages: English as an attachment in your email.

The manual is 1.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Proxxon DSH-E

Proxxon DSH-E User Manual - German - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info