Manual Protool WCP 32 (page 13 of 90) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490686

Zoom out

Zoom in

1/90

8.1 Smooth start-up

After switching on the machine, regulation elec-

tronic circuits provide for a smooth start-up up to

the operating speed without unnecessary kicks.

This decreases the wear of gears, and increases

machine lifetime.

8.2 Overload protection (detail)

The indication light [1-9] is ON (green) during nor-

mal operation. If machine load is high, the light

blinks in green colour. Under machine overload

condition, the indication light is ON (orange), and

the machine shows loss of power. When load is

removed, the machine achieves full power again.

If machine overload is present for more than 4 sec-

onds, it will be shut off. To perform a restart, the

machine must be turned off and on by the switch

[1-1]. Before commencing work again, allow the

machine to reach maximum idle speed.

8.3 Thermal overload protection

If you work with the tool for longer periods of time

under high load conditions, the thermal protection

switches the motor to cooling mode (lower speed)

that protects the motor against damage. This mode

is indicated by alternative blinking of the indication

lights in green and orange. After having cooled

down, i.e. after about 30 seconds, the machine re-

turns to the operating speed level again. In case an

overheated machine is switched off and restarted

again, the motor enters the cooling mode.

Causes of overheating: excessive pressure, de-

viation of tool from perpendicular position, bad

quality or excessive wear of disc.

9 Maintenance

- The unit should be stored in a dry place where

it is protected against freezing.

- The ventilation holes on the motor casing must

not get blocked up.

- The cable may only be replaced in a specialised

electrical workshop qualiﬁ ed to perform such

work.

After approx. 200 hours of use the following main-

tenance work must be performed:

- Check the length of the brushes. Brushes shorter

than 5 mm should be replaced.

- The machine turns itself off automatically when

the brushes are worn out. The machine must be

sent to a service centre for maintenance.

WARNING

To preserve the protection class the machine

must undergo a safety inspection; this must

be done in a specialised electrical workshop

qualiﬁ ed to perform such work.

- Service – see enclosed sheet.

10 Environmental Protection /

Disposal

Power tools, accessories and packaging should be

sorted for environmental-friendly recycling.

Only for EC countries:

Do not dispose of power tools into house-

hold waste!

According to the European Directive 2002/96/EC

on waste electrical and electronic equipment and

its incorporation into national law, power tools that

are no longer suitable for use must be separately

collected and sent for recovery in an environmen-

tal-friendly manner.

REACh

REACh is a European Chemical Directive that

came into effect in 2007. As “downstream users”

and product manufacturers, we are aware of our

duty to provide our customers with information.

We have set up the following website to keep you

updated with all the latest news and provide you

with information on all the materials used in our

existing products:

http://www.tts-protool.com/reach

11 Warranty

For our tools, we give warranty for material and

production defects in accordance with the locally

applicable legal provisions, but in any case for at

least 12 months. Within the EU member states, the

warranty period is 24 months (veriﬁ cation through

invoice or delivery note).

Damage caused by, in particular, natural wear,

overloading, incorrect handling, or damage caused

by the operator, or damage caused through use of

the equipment contrary that speciﬁ ed in the Oper-

ating Instructions, or damage which was known at

the time of purchase, is not covered by the war-

ranty. Furthermore, damage caused by the use of

non-original PROTOOL accessories and consumable

material (e.g. sanding pads) is also excluded.

Complaints can only be recognised if the tool is

returned while still assembled to the supplier or an

authorised PROTOOL Customer Service workshop.

Keep the Operating Instructions, Safety Instruc-

tions, Spare Parts List and purchase receipt in a

safe place. Otherwise the respective, current war-

ranty condi tions of the manufacturer shall apply.

Note

Due to continuous research and development work,

we reserve the right to make changes to the tech-

nical content of this documentation.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool WCP 32 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool WCP 32 Manual

Product: