490686
12
Zoom out
Zoom in
Previous page
1/90
Next page
12
To protect operating person shell be provide safety
measurement, that evaluate the exposition under
the real conditions (here are included all parts of op-
erating cycle, switch of mode and idle run mode).
6 Tool clamping
WARNING
Always disconnect the plug from the elec-
tricity network socket before carrying out
any works on the tool.
6.1 Installation of diamond discs
Put the tool down with the rotation direction arrow
[1-5] up, and press the slide unblocking [1-4] to
open while preventing the slide to get released by
a slight counter pressure.
Open the shutter [1-11] on the quick-clamp nut
[1-10], and unscrew this counter clockwise. In ac-
cordance with required cut width install diamond
discs [1-13] and spacer rings [1-12] onto the ma-
chine spindle – see gure [1c].
Tighten the quick-clamp nut [1-10] by hand, and
close the shutter [1-11].
CAUTION
Never install two discs without inserting at
least one spacer ring in between!
CAUTION
The arrow on the diamond disc must comply
with the arrow [1-5] on the tool cover!
Always install all four spacer rings, otherwise there
is a risk of injury and tool damage from loosened
discs.
It is also possible to work with one disc only.
6.2 Slotting with four discs
It is possible to work with four diamond discs at
the same time only if you replace the spacer rings
[1-12] of the basic accessories of the machine with
the special, colour-coded set of nine rings supplied
as special accessories. Caution – rings from these
two sets cannot be combined.
Always install all spacer rings, otherwise there is a
risk of injury and tool damage from loosened discs.
Adapt the speed of cut progression as well as the
pressure to the higher load of the machine.
Attention: Optimum results of work and the high-
est safety level can only be guaranteed when using
original PROTOOL accessories.
6.3 Uninstallation of diamond discs
CAUTION
Diamond discs can be very hot after cutting.
Use gloves!
Hold the diamond rings rmly, open the shutter
[1-11] on the quick-clamp nut [1-10], and loosen
the quick-clamp nut.
6.4 Adjusting the cutting depth
Rotate with the regulating wheel [1-3], until the
required cutting depth is indicated on the scale.
The values on the regulating wheel are for refer-
ence only; the depth changes with disc wear.
7 Dust exhaust
To provide for the exhaust function, connect the
hose of a PROTOOL class L, M or H exhauster (in
accordance with the type of processed material)
to the exhaust attachment [1-6].
Attention: Always work with the exhaust con-
nected. Use only exhausters with antistatic design
in order to prevent generation of static electricity
in dusty environments.
Note: check the exhauster function in case of ex-
cessive dust ejection during machine operation (see
the operating instructions for the exhauster).
8 Commissioning
Check if the data on the name plate comply with
the actual voltage of the power source.
Check if the plug connector type complies with the
socket type.
CAUTION
Use dust mask! Use hearing protection!
Operate the switch unblocking [1-2] to the rst
stage (light pressure), and switch on the tool with
the switch [1-1]. Once the motor runs with con-
stant speed, press the switch unblocking [1-2] to
second stage, cut slowly into the material down to
the pre-set depth, and then push the machine in
the cutting direction.
Based on the sort of material being slotted, and on
the spacing of installed discs (width of slot), there
are remnants of material remaining between the
slots, and these are to be removed with the sup-
plied chisel. The narrower the slot you choose, the
more material gets crushed and is removed with
the exhaust. For this purpose, there is a spacer
ring set offered as special accessories to be used
for slotting with four discs – see clause 6.2. In this
way, a wider slot is produced without the need of
chiselling out remnants of material.
RECOMMENDATION
To achieve the required results of work fast-
er and with higher ef ciency (especially in
hard materials), carry out the cuts in two
steps – pre-cut with smaller depth, and then
nish the cut down to the required depth.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool WCP 32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool WCP 32 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info