Manual Protool SSP 200 EB (page 24 of 182) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490697

Zoom out

Zoom in

1/182

5.4 Noise / Vibration Information

Measured values determined according to EN 60 745.

Typically the A-weighted noise levels of the tool are:

Sound pressure level: 92 dB (A).

Sound power level: 103 dB (A).

Acoustic output value measured according to es-

tablished guideline 2000/14/EC, appendix VI.

= 103 dB (A)

WAd

= 105 dB (A)

Measurement was performed by notiﬁ ed individual

No. ES-1014 EZU s. p. Pod Lisem 129, 171 02

Prague 71.

Inaccuracy of measurement K = 3 dB (A).

CAUTION

The noise created during work may damage hear-

ing.

► Use hearing-protective aids!

The typical hand-arm vibration is 3.4 m/s

Inaccuracy of measurement K = 1.5 m/s

Declared total value of vibrations was measured

according to standard measure method and can

be used for comparison one powertools with the

others.

Declared total value of vibrations can be used for

preliminary setting of exposition.

Warning:

Emission of vibrations during real operating can

be different from declared total value of vibrations

depending on speciﬁ c real conditions.

To protect operating person shell be provide safety

measurement, that evaluate the exposition un-

der the real conditions (here are included all parts

of operating cycle, switch of mode and idle run

mode).

6 Transport and delivery

The SSP 200 EB sword saw is delivered in per-

fect, tested condition, packed in a plastic systainer.

The oil reservoir of the machine SSP 200 EB is

not ﬁ lled. When the machine is delivered, take it

directly out of the packaging and check for poten-

tial damage during transport. Any damage caused

during transport must be reported to the carrier

immediately.

6.1 Storage

The packed sword saw can be stored in a dry stor-

age area without a heating, where the temperature

does not drop bellow −5 °C. Store the unpacked

saw only in a dry closed storage where the tem-

perature does not drop below +5 °C, and where

sudden temperature changes are prevented.

7 Adjustment

CAUTION!

All adjustments and settings must be carried out

before the machine is switched on.

WARNING

Danger of electrical injury.

Unplug any tool before handling.

Wear protective gloves!

7.1 Tilting the guide bar lengthwise

The guide bar, including the guard plate, can be

tilted 10° backward. This adjustment is mainly

used when multiple layers are cut at the same

time. It prevents resistance to the tool and an

uneven cut.

- Release lever [3-1] upward (Fig. [3a]).

- By pulling the handle, tilt the guide bar back-

wards and secure it again with the lever [3-1]

downward (Fig. [3b]).

7.2 Cutting angle adjustment

WARNING

For bevel cuts the maximum cutting depth is

limited.

Release the hand screws [4-2] on both sides. Us-

ing the bevel indicator [4-3], adjust the cutting

angle to the required value (the bevel indicator is

divided into 1° increments). Re-tighten the hand

screws [4-2].

7.3 Motor electronics

Starting current limitation

Smooth, electronically controlled starting ensures

that the machine starts without kickback. Due to

the machine’s limited starting current, a 16 A cir-

cuit breaker is sufﬁ cient.

Idle speed reduction

The electronics reduce the machine’s RPM during

idle, which also decreases wear to the motor and

gears.

Constant electronics

Constant electronics maintain the RPM the same at

idle and under load, which ensures uniform work

movement and a high-quality cut.

Electronic overload protection

If the machine is extremely overloaded, electronic

protection guards the motor from damage. In this

case, the motor stops and resumes only after dis-

charge, and after the switch is engaged again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool SSP 200 EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool SSP 200 EB Manual

Product: