Manual Protool RGP 80-11 E (page 14 of 148) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490681

Zoom out

Zoom in

1/148

4 Control Elements

[1-1] Additional handle

[1-2] Switch lever

[1-3] Adjusting wheel

[1-4] Handle

[1-5] Knob

[1-6] Backstop bar

[1-7] Suction ﬂ ange

[1-8] Scale

[2-1] Bolt

[2-2] Retainer

[2-3] Washer

[2-4] Milling rings

[2-5] Tool carrier

[2-6] Guide surface

[2-7] Bolt

[2-8] Sliding part

[2-9] Slot

[2-10] Suction ﬂ ange

[2-11] Guide surface

Not all of the accessories illustrated or de-

scribed are included as standard delivery.

5 Notes on Safety

Prevention

DANGER

5.1 General Safety Instructions

- Before using the machine, carefully read

all safety instructions and the Operating

Instructions.

- Keep all of the attached documents and

pass on the documentation if the ma-

chine changes ownership.

5.2 Safety instructions for all

work activities

Safety warnings common for the

following works: grinding, surface

grinding, grinding with wire brush or

abrasive cutting:

a) This electromechanical tool is de-

signed to be used as a surface grinder

or a cutter with a cutter head. Read

all safety warnings, instructions, il-

lustrations and speciﬁ cations intend-

ed for this electromechanical tool.

Failing to meet all the below speciﬁ ed

instructions may lead to injury by electric

current, ﬁ re and/or serious injury.

b) This tool is not recommended for pol-

ishing or cutting. Execution of works

this tool is not designed for may create

a risk and cause injury of a person.

c) Do not use accessories which is not

explicitly designed and recommended

by the tool manufacturer. The fact that

the accessories an be attached to your tool

does not guarantee its safe operation.

d) Nominal rpm of accessories must be

at least equal to the maximum rpm,

stated on the tool. Accessories that op-

erate at higher rpm than are the nominal

rpm, may break and pull apart.

e) Outer diameter and thickness of your

accessories must be within the limits

of nominal range for your electrome-

chanical tool. Accessories of incorrect

dimensions cannot be either protected

enough or controlled properly.

f) Clamping dimensions of disks, ﬂ anges,

supporting plates or any other acces-

sories must be suitable for ﬁ xing to

the tool spindle. Accessories with clamp-

ing holes which do not correspond with the

mounting dimensions of electromechani-

cal tool will be unbalanced, may vibrate

excessively and cause loss of control.

g) Do not use damaged accessories.

Check the accessories prior to each

use: check the grinding wheels for

chips and cracks, check the sup-

porting plates for cracks, ripping

or excessive wear, check the wire

brushes for loose or cracked wires. If

accessories or tool fell down, check

the damage or mount undamaged

accessories. After the accessories

is checked and mounted, you and

also bystanders stand to be beyond

the level of rotating accessories and

leave the tools run free at highest

rpm for one minute. During this trial

time damaged accessories usually rips

apart or disintegrates.

h) Use personal protective means. De-

pending on use, use facial shield and

safety protective goggles. If appro-

priate, use dust mask, ear protec-

tors, gloves and work apron, capa-

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool RGP 80-11 E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool RGP 80-11 E Manual

Product: