490710

Protool PLP 205 Manual

10
Zoom out
Zoom in
Previous page
1/92
Next page
Operating the electric tool
for a first time
Remaining risks
Safety instructions
10
GB
This electric tool may only be used,
maintained and repaired by the people who
have received the relevant instructions.
These people must have reached the
minimum age legally required. For safe work
and familiarizing with all the remaining risks,
they must have read and understood this
Operating Manual.
1. For maximum safety of work with this
electric tool, read this Operating Manual
carefully and observe all the instructions
given herein.
2. Follow the safety instructions supplied
separately as a part of delivery with each
electric tool.
3. The electric tools shall not be used in damp
or wet locations, outdoors in the presence of
rain, fog, snow, or if there is a risk of fire or
explosion.
4. Check the power supply cord and plug
before each use of the electric tool. Have
any defect repaired by a professional service
workshop.
5. Remove plug from the mains before
performing any work on the electric tool.
6. Only insert plug in the mains socket when
the electric tool is switched off by the mains
switch. Always keep the power supply cord
back away from the electric tool while
working and allow the cord to move freely in
the whole working area to make trouble-free
work possible.
7. When working outdoors, use exclusively the
extension cords and cable connectors
attested for outdoor use.
8. The electric tool may only be started after
placing it on the workpiece in initial position.
9. Keep hands away from the chip discharge
channel. If the channel is blocked, first the
electric tool must be switched off and
allowed to come to a complete standstill.
After that, the chips may be removed.
10. Secure work in a safe position with enough
support for a workpiece and the electric tool.
11. Whenever possible, the electric tool should
be connected to the mains via a fault current
circuit breaker (Fl) or a PRCD safety device.
12. This electric tool is not intended for
stationary use.
13. The dust originating from planing wood is
hazardous to health. Connect the dust
extraction adapter and wear a dust mask
when working with the electric planer.
14. Turn or exchange blunt knives in good time,
the risk of kickback is otherwise increased.
15. After planing is finished, only put the planer
aside after the cutting head has come to a
complete standstill.
16. Damaged power supply cords must be
replaced immediately by a specialist.
17. Unauthorized use of this product anyway
may lead to a personal injury.
18. Repairs shall be carried out by the qualified
personnel only.
19. Use only the original spare parts.
20. Use safety glasses and ear protection.
21. Use only the original cutting heads identical
to the one supplied with the electric tool.
Even when the electric tool is used properly and
all the relevant safety measures are followed,
the following remaining risks can still occur due
to the design of the electric tool required for the
intended working operations:
- Contact with the cutting blades during
rundown;
- Clothing can be caught by the rotating parts;
- Hazards invited by the flexible supply cord;
- Hazards invited by the harmful dust when
using the planer for a long time without a dust
extractor.
- Check if the data on the nameplate
correspond with the actual voltage of the
power supply.
- The electric tools with rated voltage 230 V
may be also connected to 220 V.
- Fusing for 230 V: 16 A slow-action fuse or
equivalent automatic circuit breaker.
- The planer is equipped with the overload
cut-out and LED overload indicator. The
overload cut-out protects the motor against
excessive overloading.
- Use only extension cords with a cross section
of 3 x 1,5 mm , max. 20 m length
(3 x 2,5 mm , max. 50 m). When the electric
tool is used outdoors, use only extension
cords intended for outdoor use and so
marked.
2
2
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool PLP 205 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool PLP 205 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info