490691

Protool MXP 1000 Manual

13
Zoom out
Zoom in
Previous page
1/88
Next page
13
- By pulling on the stirrer rod, you can pull the
ErgoFix adaptor [1-8] out of the machine spin-
dle. In this way, you can adjust fi ve different
working heights. One step is 2 cm. The maxi-
mum adjustment movement is 8 cm and the
end position is signalled by reaching the groove
[2-2] on the ErgoFix adapter.
- Then release the clamping ring of the ErgoFix
adapter [1-7] and check that the adapter [1-8]
is seated securely in the machine spindle.
Quick change function
NOTE
Ensure that the adapter [1-8] remains
clean.
Do not lubricate the adaptor [1-8].
Only press the ErgoFix casing [1-7] when
the machine is not in operation.
The ErgoFix interface enables you to easily and
quickly remove the stirrer rod from the machine.
- Push the clamping ring of the ErgoFix adapter
[1-7] in the direction of the machine to move it
as far as it goes and hold it tight.
- By pulling on the stirrer rod, you can pull the
ErgoFix adaptor [1-8] completely out of the ma-
chine spindle.
Changing the stirrer
► Adapter ErgoFix [2-1] after worn-out of stirrer
rod can be reused.
Set the wrench [2-3] on the hexagon of the stirrer
endpiece [2-4] and turn to the left to screw the
stirrer rod out of the ErgoFix adapter [2-1].
6.6 Stirrer
To mix different material mixtures together, use
different PROTOOL stirrers: see the catalogue
PJ Uni
For wall paints,
emulsion paints,
ready-made fi ller,
ready-mix plaster,
varnishes/glazes
RS
For wall paints,
emulsion paints,
pastes, varnishes
casting compounds,
bitumen, sludges
HS2
For tile adhesives,
joint sealant, adhe-
sive mortar, ready-mix
plaster, screed, fi llers,
levelling compounds
HS3R
For mortar, concrete,
cement and lime
plaster adhesive fi ller,
screed, quartz-fi lled
epoxy resin, thick
bitumen coating
HS3L
For gypsum plaster,
emulsion paints,
varnishes wall paints,
casting compounds
WS
For paints, varnishes,
wall paints, emulsion
paints, plasters, glues,
tile adhesives
CS
For balancing weights,
fi llers, sealants,
adhesives
6.7 Mains connection
WARNING
There is a risk of accidents occurring if you
do not use the correct power supply.
The stirrer must only be operated with a single-
phase alternating current with a nominal voltage of
220–240 V/50–60 Hz. In the 2nd level, the machine
is protected against accidents caused by electrical
current in accordance with the standard EN 60 745-1
and it has built-in radio interference suppression in
accordance with the standard EN 55 014.
Before starting up the machine, check that the
specifi cations on the type plate correspond to the
actual voltage of the power supply.
If required, you can extend the fl exible power cable
as follows:
- Length 20 m, conductor cross-section
3×1.5 mm
2
- Length 50 m, conductor cross-section
3×2.5 mm
2
Only use extension cables that are suitable for
outside use and that are marked accordingly.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool MXP 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool MXP 1000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info