Manual Protool CSP132 (page 13 of 73) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490703

Zoom out

Zoom in

1/73

24 25

Unscrew the following components:

Plate [5-1] covering the blade guard

Guard [5-2] covering the pendulum mount

Dust exhaustion connection [5-3]

Riving knife [5-4]

Ensure the curve-cutting head [7-3] is clean

and tted according to the illustration and

screw it tight. Ensure that the mounting ange

[7-1] and the clamping ange [7-2] are in the

correct position. The holes in the curve-cutting

head [7-3] must t onto the follow-up pins on

the mounting ange [7-1]. Insert the pin [7-4]

into the hole on the curve-cutting head to se-

cure it.

Screw the cover guard [7-5] onto the pendu-

lum mount [7-6].

Screw the cover guard [7-7] onto the blade

guard [7-8].

Select the depth to be milled as described in

Section 7.2 (Cutting Depth Adjustment) and

the angle to be milled as described in Section

7.3 (Cutting Angle Adjustment).

You can check the curve depth against the

angle to be milled on the table on the blade

guard.

10 Maintenance 

- The unit should be stored in a dry place

where it is protected against freezing.

   WARNING

To verify that  the protective  insulation 

remains  intact,  the  machine  must  be 

subjected to  a technical  safety test  af-

terwards. 

For this reason, this work must be per-

formed  exclusively  by  a  professional 

electro-workshop. 

- With each changing of the saw blade, re-

move deposited saw dust from the inside of

the protective guard.

- The ventilation slots on the motor casing

should be cleaned out from time to time.

After an operating period of approx. 200 hours,

the following maintenance work must be per-

formed:

- Check the motor brushes and replace if

necessary. Clean the motor housing.

- Renew the grease lling of the gear box.

11  Environmental Protection/

Disposal 

Power tools, accessories and packaging should

be sorted for environmental-friendly recycling.

 Only for EC countries:

Do not dispose of power tools into 

household waste!

According to the European Directive 2002/96/

EC on waste electrical and elec tronic equip-

ment and its incorporation into national law,

power tools that are no longer suitable for use

must be separately collect ed and sent for re-

covery in an environmen tal-friendly manner.

REACh

REACh is a European Chemical Directive that

came into effect in 2007. As “downstream

users” and product manufacturers, we are

aware of our duty to provide our customers

with information. We have set up the following

website to keep you updated with all the latest

news and provide you with information on all

the materials used in our existing products:

http://www.tts-protool.com/reach

12 Warranty 

For our tools, we give warranty for mate-

rial and production defects in accordance with

the locally applicable legal provisions, but in

any case for at least 12 months. Within the

EU member states, the warranty period is 24

months (verication through invoice or deliv-

ery note).

Damage caused by, in particular, natural wear,

overloading, incorrect handling, or damage

caused by the operator, or dam age caused

through use of the equipment contrary that

specied in the Operating In structions, or dam-

age which was known at the time of purchase,

is not covered by the warranty. Furthermore,

damage caused by the use of non-original

PROTOOL accesso ries and consumable mate-

rial (e.g. sanding pads) is also excluded.

Complaints can only be recognised if the tool

is returned while still assembled to the supplier

or an authorised PROTOOL Cus tomer Service

workshop. Keep the Operat ing Instructions,

Safety Instructions, Spare Parts List and pur-

chase receipt in a safe place. Otherwise the

respective, current warranty condi tions of the

manufacturer shall apply.

Note 

Due to continuous research and develop ment

work, we reserve the right to make changes

to the technical content of this documentation.

13 Declaration of Conformity 

Hand Circular Saw  Serial no. 

CSP 132 E  638479

We declare under our sole responsibility that

this product is in conformity with the following

standards or standardization doc uments:

EN 55 014-1, EN 55 014-2, EN 60 745-1,

EN 60 745-2-5, EN 61 000-3-2, EN 61 000-3-3

according to the provisions of the regula tions

2006/42/EC, 2004/108/EC.

Stanislav Jakeš

Research and development

Protool GmbH

Wertstr. 20

D-73240 Wendlingen

29.12.2009

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool CSP132 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool CSP132 Manual

Product: