Manual Protool CSP132 (page 12 of 73) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490703

Zoom out

Zoom in

1/73

22 23

7.4  Cut indicator 

The cut produced by the CSP 132 E depends

on the bevel setting and can be observed at

the cut indicator.

7.5  Parallel Guide 

Various parallel guides can be inserted into the

machine base plate [2-2] on the left [2-3] and

on the right [2-4].

Tighten the parallel guide using the winged

screws [2-1].

7.6  Exhaustion 

    CAUTION

Inhaled  dust  may  damage  the air  pas-

sages. 

► Tools should be permanently connected to

the dust exhausting plant.

► Wear respirator if you work with dust.

To exhaust dust, suction adapter [1-1] can

be mounted on the sawdust ejector through

which common exhaust hoses of exhausters

can be connected.

7.7  Replacing the Saw Blade 

    WARNING

Before  exchanging  the  saw  blade,  pull 

the mains  plug  from  the  power  sup ply 

socket. 

Wear protective gloves! 

The sawing performance and the quality of the

cut depend essentially on the condition and

tooth form of the saw blade. Therefore, use

only sharp saw blades that are suitable for the

material to be worked.

Swing back the swinging guard with the lever

[3-5].

Install a suitable saw blade according to the

illustration and tighten. Take care that the

mounting ange [3-4] and the clamping ange

[3-2] are correctly positioned. The holes in the

saw blade [3-3] must t onto the follow-up

pins on the mounting ange [3-4].

   WARNING

Observe for installation: The cutting di-

rection of the teeth (arrow on  the  saw 

blade) must match the direction of the 

arrow on the guard. 

Check  the  function  of  the  swinging 

guard. 

Tighten the hexagon bolt [3-1] using the SW19

Allen key supplied, while holding the clamping

ange [3-2] with the single ring spanner which

is also supplied.

To remove the blade, follow the same sequence

in reverse.

8  Operating Instructions 

► Do not cut into nails, screws, etc.

► Do not work with materials containing as-

bestos.

► Do not use saw blades that have cracks or

that are damaged.

► Under no circumstances use abrasive

disks!

► Saw blades of highly alloyed, high-speed

steel (HSS-steel) must not be used.

► Feeding too fast signicantly reduces the

performance of the machine and short ens

the life of the saw blade.

► Use only sharp saw blades in perfect con-

dition.

► Uncoated saw blades can be protected from

corrosion with a thin coat of acid free oil.

► Resin and glue on the saw blade cause poor

cutting results. Therefore, clean the saw

blade immediately after use.

8.1  Working different materials

Wood 

The proper selection of the saw blade is de-

pendent on the type and quality of the wood

as well as whether the wood is to be sawed

along or across the grain. Beech and oak dust

is especially detrimental to health and there-

fore should be worked only with vacuum dust

extraction.

Plastic 

When cutting plastic, especially PVC, long, spi-

ral shaped shavings are produced that can be

electrostatically charged.

This can cause the ejector to become clogged

and the swinging protective guard [1-8] to

stick. The use of a vacuum cleaner for dust

extraction is recommended.

Apply the machine running against the work-

piece and carefully start sawing. Then saw

steadily and without interruption so that the

saw teeth have less chance of sticking.

Non-ferrous Metals 

Use only a suitable and sharp saw blade. This

ensures a clean cut and prevents jam ming of

the saw blade.

Apply the machine running to the workpiece,

carefully start sawing and then saw with slow

feeding and without interruption.

For proles, always start the cut on the small

side; for U-proles, never start the cuts on the

open side.

Support long prole, otherwise the saw blade

can become jammed when the prole tips over

and the machine can “kick back”.

Material with Mineral Content (Light 

building material) 

► Only dry cutting is permitted.

► Use vacuum dust extraction. The vacu um

cleaner must be suitable for masonry dust.

8.2  Two-Man Operation

The machine has several handholds to allow it

to be used by one or two operators, depending

on the conguration.

Illustration 4a is for one-man operation.

Illustration 4b is for two-man operation.

9  Using Attachments

You can extend the use of your circular saw by

using the NS-CSP 250x50 planing attachment

and the RS-CSP 160x80 curve-cutting attach-

ment available from the Protool range.

    WARNING

Risk of electric injury. 

► Before any manipulation with the tool make

sure to unplug the mains socket outlet.

9.1  NS-CSP 250x50 Planing 

Attachment

Using the planing attachment (item no. 624

337), you can mill grooves and rabbets to a

max. depth of 80 mm and a width of 50 mm

(see diagrams below).

max 80 mm

max 36 mm

50 mm

80 mm

Set the saw to minimum cutting depth.

Remove the saw blade [3-3] by following the

instructions in Section 7.7 (Replacing the saw

blade).

Unscrew the following components:

Plate [5-1] covering the blade guard

Guard [5-2] covering the pendulum mount

Dust exhaustion connection [5-3]

Riving knife [5-4]

Ensure the planing head [6-3] is clean and t-

ted according to the illustration and screw it

tight. Ensure that the mounting ange [6-1]

and the clamping ange [6-2] are in the cor-

rect position. The holes in the planing head

[6-3] must t onto the follow-up pins on the

mounting ange [6-1]. Insert the pin [6-4]

into the hole on the planing head to secure it.

Screw the cover guard [6-5] onto the pendu-

lum mount [6-6].

Screw the cover guard [6-7] onto the blade

guard [6-8].

Select the depth to be milled as described in

Section 7.2 (Cutting Depth Adjustment).

9.2  RS-CSP 160x80 Curve-Cutting 

Attachment

Using the curve-cutting attachment (item no.

624 339), you can sink grooves, mill and cut

curves as illustrated below. For this purpose,

the curve-cutting attachment swivels by up to

45°.

80 mm

max 56 mm

max 50 mm

80 mm

45°

Set the saw to the minimal cutting depth.

Remove the saw blade [3-3] by following the

instructions in Section 7.7 (Replacing the saw

blade).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool CSP132 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool CSP132 Manual

Product: