490707
27
Zoom out
Zoom in
Previous page
1/220
Next page
27
We guarantee appliances in accordance with sta-
tutory/country-specific regulations (proof of
purchase by invoice or delivery note).
Damages attributable to normal wear and tear,
overload or improper handling will be excluded
from the guarantee.
In case of compliant please send the machine, un-
dismantled, to your dealer or the Service Centre
for electric power tools.
We declare under our sole responsibility that this
product is in conformity with the following stan-
dards or standardization documents:
EN 50 144-1, EN 55 014-1, EN 55 014-2,
EN 61 000-2-3, EN 61 000-3-3,
according to the provisions of the regulations
89/336/EEC, 98/37/EC
Manfred Kirchner
Subject to change
Defects and their removal
Defect Cause Removal
The machine will not run
There is no current supply
Check safety fuses and supply
wires
Worn brushes Replace brushes
Stuck switch Press a safety fuse
When overloaded Check safety fuses
The cut is not clean, the chain
goes to the side
Too big shift into the cut Reduce the shift
Blunt tool
Sharpen the chain, or replace it
with a new one
The chain is not properly
sharpened Replace the chain with a new one
Cutting without a stop gui-
dance Use the stop guidance
Required big power to shift the
machine into the cut
Supporting area of the
sleigh is dirty
Clean it and lubricate it with gliding
wax
Blunt tool
Sharpen the chain, or replace it
with a new one
Different qualities of wood
Adjust the size of the shift to the
cut
Too big shift for the cut Reduce the shift
The chain is not lubricated Blocked lubricating chan-
nels of the guide reglet Clean the guide reglet
Defected dose oil pump
Replace the pump (in an authori-
sed service workshop)
Empty oil tank Replenish chain oil
Inner oil channels of the
machine are blocked
Clean the machine (in an authori-
sed service workshop)
Guarantee
Declare of conformity
kniha_Narex_CPP380.book Seite 27 Mittwoch, 31. Oktober 2001 11:53 11
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool CCP 380 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool CCP 380 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info