738854

Protector AS-8000 Manual

34
Zoom out
Zoom in
Previous page
1/88
Next page
8. Lay the wire to the stove transmitter.
9. Connect the wire on the thermal sensor to the stove
transmitter and the wire marked in red to the screw
ROT / RED and the wire marked in black to the screw
SCHWARZ / BLACK.
10. There is a wall mount on the back of the stove
transmitter. This can be pushed down and removed
from the stove transmitter.
11. Remove the cover from the stove transmitter and insert
the 2 x AA batteries with the correct polarity as marked.
Then you can slide the cover back on.
12. Look for a suitable location to attach the stove
transmitter and screw the wall bracket for the
transmitter into place. The stove transmitter should be
at least 50 cm away from the exhaust pipe so that the
transmitter cannot be destroyed by heat. Also the stove
transmitter should not be attached behind cladding as
this limit its range.
INITIAL OPERATION
Encoding
The exhaust control unit is encoded at the factory and
does not necessary need to be taught at initial
operation. If there are faults and/or function errors then
carry out the following encoding steps. This recreates
the structure of the exhaust controls.
Brief instructions
Factory settings
Press and hold the reset button
The unit will beep once after approx. 1 second and
4 green LEDs will flash.
There will be 3 beeps after another 7 seconds
followed by a pause and 3 more beeps. The
power LED will light constantly
Release the reset/learn button; the device is now
set to default
Teaching the sensors:
(All the sensors to be taught are ready for operation)
Briefly press the reset button on the central unit
1 beep will sound after approx. 1 second and the
4 green LEDs will flash
Now briefly press the set button on sensor 1
After approx. 10 seconds the LED will light
constantly depending on the sensor type
(window, roller shutter, stove contact) and will
beep once for sensor 1 and n times for sensor n
Press the set button on the next sensor within
50 seconds of the beep.
After the last sensor wait 50 seconds. The central
unit will go into default status and display the
condition of each sensor. The central unit is
ready for operation.
Logical associations:
Window closed
Window LED red
Window open
Window LED green
Stove on
Stove LED red
EN
34
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protector AS-8000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protector AS-8000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info