Manual Protector AS-8000 (page 33 of 88) (English, German, Dutch, French)

738854

Zoom out

Zoom in

1/88

• The contact must be attached to the top or side window

frame and casement in such a way that the distance

between the two casing sections is less than 6 mm

when the window is closed! Use the included packing

(U) to make these adjustments.

• We recommend attaching the contact and the magnet

with the double-sided sticky tape before the ﬁnal

attachment and only to screw them in place at the end.

Testing the function of the roller

shutter sensor

• Slowly move the roller shutter to the open position,

then the green LED on the roller shutter sensor (OPEN)

will ﬂash brieﬂy before the open position.

• Close the roller shutter, then the red LED (CLOSED) will

ﬂash brieﬂy.

Instructions for attaching the

stove transmitter

AS-T30 (ﬁgures 15 and T)

NOTE

The stove should be switched off and cool in order to

avoid burns to your skin.

The thermal sensor (ﬁgure 3) is fed into the exhaust

pipe through a hole and screwed to the stove pipe using

the included mounting bracket. The stove transmitter

should not be covered by cladding as this impedes the

radio signal and reduces the range.

1. Drill a 4 mm hole in a suitable position in the exhaust

pipe for the thermal sensor. If possible ensure that the

hole is positioned in such a way that the thermal sensor

cannot be seen after attachment.

2. Slide the mounting bracket over the thermal sensor but

do not tighten the screw to attach the thermal sensor yet.

3. Insert the thermal sensor as far as possible into the hole

that you have drilled for it.

4. Move the mounting bracket on the thermal sensor

until it is lying on the exhaust pipe and then mark the

two attachment holes on the mounting bracket with a

suitable pen. Then remove the thermal sensor and the

mounting bracket from the exhaust pipe again.

5. Drill 2 mm holes at the two positions you have marked

for mounting on the exhaust pipe.

NOTE

If you have a double-walled exhaust pipe then take

care to drill the mounting holes only through the

outer pipe.

6. Fix the mounting bracket to the exhaust pipe by

screwing it with the two included tapping screws and

the two drilled holes as described above.

7. Now feed the thermal sensor through the mounting

bracket as far as possible and ﬁx it to the mounting

bracket using the side screw. Do not tighten the screw

too far to avoid damage to the thermal sensor.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protector AS-8000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protector AS-8000 Manual

Product: