490657

Prosun 3000 Series Manual

8
Zoom out
Zoom in
Previous page
1/17
Next page
GENERAL ELECTRICAL NOTES
• ALL ELECTRICAL WORK SHALL COMFORM TO THE REQUIREMENTS OF THE NATIONAL
ELECTRICAL CODE, O.S.H.A. OR APPLICABLE LOCAL AND OR STATE ORDINANCES, AS WELL
AS UTILITY COMPANY RULES REGARDING AMPERE INTERUPTION AND SAFETY SHUNT TRIP
SWITCHES AND POWER PANELS OF WHICH SHALL BEAR THE LABEL OF UNDERWRITER’S
LABORATORIES, INCORPORATED AND SHALL BE PERMANENTLY MARKED FOR EASY
IDENTIFICATION.
• ALL WIRES SHALL BE SINGLE SOLID RUNS WITHOUT SPLICES MEETING THE N.E.M.A.
STANDARDS
• THE ELECTRICAL CONTRACTOR SHALL PROVIDE AND INSTALL ALL ELECTRICAL
MATERIAL AS SPECIFIED FOR A SAFE OPERATING SYSTEM.
• THE ELECTRICAL CONTRACTOR SHALL RING OUT AND TAG AND TERMINATE ALL WIRES AT
BOTH ENDS, WITH EACH RUN TO BE INSPECTED TO ENSURE THAT NO WIRES HAVE BEEN
GROUNDED OR OPEN.
• THE CUSTOMER SHALL PROVIDE A DEDICATED POWER SOURCE WHEN CALLED FOR BY
PROSUN, ITS DEALERS, DISTRIBUTORS OR OTHER DESIGNATED AGENTS.
• ProSun
®
, ITS DEALERS, DISTRIBUTORS OR OTHER DESIGNATED AGENTS ARE NOT
RESPONSIBLE FOR THE FINAL INSTALLATION OF THE ELECTRICAL SYSTEM. THE
RECOMMENDED ELECTRICAL PLAN MUST BE COORDINATED BETWEEN THE CUSTOMER
AND THE ELECTRICAL CONTRACTOR. ANY DEVIATION TO THE ELECTRICAL PLAN BEFORE,
DURING AND AFTER EQUIPMENT INSTALLATION IS THE RESPONSIBILITY OF THE
CUSTOMER.
• THE ELECTRICAL CONTRACTOR SHALL ENSURE THE COMPLETION OF ALL ELECTRICAL
REQUIREMENTS PRIOR TO THE INSTALLATION OF ANY ProSun
®
SYSTEM.
REVISED: 11/20/01 Page 7
… 8 …


Need help? Post your question in this forum.

Forumrules
1

Forum

prosun-3000-series

Reset search

  • I have a 2004 Prosun tanning bed model 3000 I just moved it. When I plug it in the display says (81.6) and beeps. It won't turn on. What might be the issue? Submitted on 9-8-2023 at 18:40

    Reply Report abuse

  • I have a 2004 Prosun tanning bed model 3000. We just moved it. When I plug it in the display beeps and says (81.6) It won't turn on. What is the issue with it? Submitted on 9-8-2023 at 18:38

    Reply Report abuse

  • My tanning bed is beepiing and looks like a code 81.6 and Submitted on 18-8-2019 at 06:16

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Prosun 3000 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Prosun 3000 Series in the language / languages: English as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info