566799

Profile PIN-146 Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
２
Overload protection: 250V DC/250Vrms AC
3.2.5 Diode test and Audible continuity test
Range
Description
Test condition
“ ”
Built-in buzzer sounds if
resistance is less
than 70Ω
Open circuit voltage
aprox. 3V
Overload protection: 250V DC/250Vrms AC
3.2.6 BACK LIGHT
Press “ ” button to turn on the backlight, it will automatically
turn off after approximately 5 seconds.
4. OPERATION
4.1 DC Voltage Measurement
1) Connect the black test lead to "COM" socket and red test lead
to the "V" socket.
2) Set the selector switch to "500 V " position.
3) Measure the voltage by touching the test lead tips to the test
circuit.
4) Read the result from the LCD panel.
5) Push the DH switch to "ON" to lock display value, push it to
"OFF" to exit.
4.2 AC Voltage Measurement
1) Connect the black test lead to "COM" socket and red test lead
to the "V" socket.
2) Set the selector switch to "500V " position.
3) Measure the voltage by touching the test lead tips to the test
circuit.
4) Read the result from the LCD panel.
5) Push the DH switch to "ON" to lock display value, push it to
"OFF" to exit.
4.3 AC Current Measurement
1) Set the selector switch to the desired "2A ”、"20A ”、or
"400A ” position.
2) Open the clamp by pressing the jaw-opening handle and insert
the cable to be measured into the jaw.
3) Close the clamp and get the reading from the LCD panel.
4) Push the DH switch to "ON" to lock display value, push it to
"OFF" to exit.
Note:
A) Before this measurement, disconnect the test lead with the
meter for safety.
B) If the current range is not known before hand, set the selector
switch to the highest range and work down.
4.4 Resistance Measurement
1) Connect the black test lead to "COM" socket and red test lead
to the "Ω" socket.
2) Set the selector switch to "200Ω，20kΩ or 2000kΩ” position.
3) Connect the tip of the test leads to the points where the value
of the resistance is needed.
4) Read the result from the LCD panel.
5) Push the DH switch to "ON" to lock display value, push it to
"OFF" to exit.
Note:
When taking resistance value from a circuit system, make sure
the power is cut off and all capacitors are discharged.
5. Battery replacement
1) When the battery voltage drops below proper operation range
the " " symbol will appear on the LCD display and the batteries
need to be changed.
2) Before changing the batteries, set the function switch to "OFF".
3) Replace the old batteries with the same type of batteries.
4) Close the bottom case and fasten the screw.
6. MAINTENANCE
1) Before opening the bottom case, disconnect both test leads
and never use the meter before the bottom case is closed.
2) To avoid contamination or static damage, do not touch the
circuit board without proper static protection.
3) If the meter is not going to be used for a long time, take out the
battery and do not store the meter in high temperature or high
humidity environment.
4) When taking current measurement, keeping the cable at the
center of the clamp will get more accurate test results.
5) Repairs or servicing not covered in this manual should only be
done by qualified persons.
6) Periodically wipe the case with a dry cloth and detergent. Do
not use abrasives or solvents on this instruments.
7. WARRANTY
The guarantee period for PIN-146 amounts to 2 years and commences on the date
of purchase. During the guarantee period ELTRA NV will repair any defects
attributable to material or production faults. ELTRA NV may choose to either repair
or replace a defective appliance.
ELTRA NV is not obliged to repair or replace appliances if they have become
defective as a result of damage, inappropriate use, or modifications or adaptations
made after the purchase date.
Take any defective appliance together with the original receipt back to the shop
where the appliance was sold. Always add a note with a description of the problem.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Profile PIN-146 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Profile PIN-146 in the language / languages: Dutch as an attachment in your email.

The manual is 1,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info