807258

Pro-User TPMS2 Manual

6
Zoom out
Zoom in
Previous page
1/44
Next page
6
4. Alarm Settings and Measurement Unit
When any alert is received, it is recommended to slow down your car and
proceed to a safe stopping location, where the tyres can be examined. An alarm
will occur if the tyre temperature exceeds the value of the HIGH TEMPERATURE
alarm setting or the tyre pressure is lower than the LOW PRESSURE alarm
setting or higher than the HIGH PRESSURE alarm setting.
Note: After 20 seconds idle, the main unit will exit the settings mode. Please read the
following steps first and prepare your workplace. If you exceeded the time limit you have
to start over again. If you enter values that exceed the capabilities of the unit, the
maximum possible values are entered for it.
To change the alarm settings and the measurement unit follow these steps:
1. Enter the Settings Mode by pressing the SET button for 3 seconds
(the LEARNING icon is flashing (1)
2. Press the RIGHT button (the SETTINGS icon is flashing)
3. Press the LEFT button to enter the Menu and see the HIGH PRESSURE ALARM
setting. The factory setting (2) is 3.0 bar (TPMS4) / 5.0 bar (TPMS2)
4. Press the LEFT button to edit the HIGH PRESSURE ALARM (2) settings (the first
digit blinks) or the RIGHT button to skip.
5. If you chose to edit the setting, use the RIGHT button to change the value of the
digit. Use the LEFT button to change to the next digit and confirm the current
number. After confirming the second digit, the changes are saved and the unit
beeps. Exit the settings menu by pressing 2x SET or continue as follows:
6. Press the RIGHT button to go to the LOW PRESSURE ALARM settings. The factory
setting is 2.0 bar/29 psi (3).
7. Press the LEFT button to edit the LOW PRESSURE ALARM (3) settings (the first
digit blinks) or the RIGHT button to skip.
8. If you chose to edit the setting, use the RIGHT button to change the value of the
digit. Use the LEFT button to change to the next digit and confirm the current
number. After confirming the second digit, the changes are saved and the unit
beeps. Exit the settings menu by pressing 2x SET or continue as follows:
9. Press the RIGHT button to go to the HIGH TEMPERATURE ALARM settings.
10. Press the LEFT button to edit the HIGH TEMPERATURE ALARM (4) settings (the
first digit blinks) or the RIGHT button to skip.
11. If you chose to edit the setting, use the RIGHT button to change the value of the
digit. Use the LEFT button to change to the next digit and confirm the current
number. After confirming the second digit, the changes are saved and the unit
beeps. Exit the settings menu by pressing 2x SET or continue as follows:
12. Press the RIGHT Button to change the display to the PRESSURE UNIT setting (5).
The current unit blinks. Use the LEFT button to change the measurement unit.
Exit the settings menu by pressing 2x SET.
(3) LOW PRESSURE ALARM (4) HIGH TEMPERATURE ALARM (5) MEASUREMENT UNIT
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-User TPMS2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-User TPMS2 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 4.83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info