Manual Pro-User DRC4310DC (page 9 of 64) (English, German, Dutch, French)

807540

Zoom out

Zoom in

1/64

3. Mount the license plate on the license plate bracket.

4. Choose a routing path for the camera’s power cable through the vehicle’s body to the reverse light

circuit. If in doubt, seek professional installation assistance.

Some vehicles may have a hole available to pass the wire through, such as where the license plate

light is mounted, or you can drill a hole close to where the power cable is attached to the camera.

Once you have chosen where the cable will enter the vehicle’s body, remove the camera.

If you are

able to use an existing opening, skip the next two steps.

6. Before you drill a hole, you MUST CHECK and see WHAT IS BEHIND WHERE YOU ARE DRILLING. If

there are any vehicle components, such as electrical parts or fuel system components behind where

you are drilling, you must take whatever precaution is necessary not to damage them. Remove the

license plate and camera before drilling.

7. After you have drilled the hole, insert the supplied grommet, then pass the camera cables through

the grommet into the vehicle. You must use the grommet to prevent the metal edge of the hole from

cutting the camera cable.

8. Next, you’ll need to find the vehicle’s reverse lights. Turn the vehicle’s ignition key to the accessory

position, engage the parking brake and put the car in reverse. Look at the vehicle’s tail lights to see

where the reverse lights are located, they are the white lights. To locate the reverse light’s 12V/24V

+ wire it will be necessary to gain access to the rear of the vehicle’s tail light. For help locating the

vehicle’s reverse light circuit contact your vehicle’s manufacturer for vehicle specific wiring diagrams.

9. Once you have located the reverse light circuit you will have to route the camera cable to that

location. You must securely fasten the power cable to prevent it from being caught on any vehicle

component such as the trunk hinge.

Never

route the cable on the outside of the vehicle!

The reverse light sockets on most vehicles have two

wires connected to them. Usually the negative wire is

black and the positive wire is a coloured wire. If you are

uncertain about the wiring, you can use a 12V/24V

multimeter available at most auto parts stores to

determine which is the positive wire. Follow the

manufacturer’s instructions for the safe use of the

multimeter.

10. After determining which wire is the positive and which is the negative, turn off the ignition key,

then remove the battery’s negative cable.

11. Splice the red wire using the supplied in-line wire connectors to the reverse light’s positive (+) wire.

Use a set of slip joint pliers to squeeze the TAP and insure good connection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pro-User DRC4310DC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 10.34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pro-User DRC4310DC Manual

Product: