553941
9
Zoom out
Zoom in
Previous page
1/36
Next page
9
9. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included hex keys in a secure place. The large hex key is used to adjust the walking
belt (see pages 26 and 27). To protect the floor or carpet, place a mat under the treadmill. If there is a sheet
of clear plastic on a decal, remove the plastic.
If you purchase the optional chest pulse sensor (see page 22), follow the steps below to install the re-
ceiver included with the chest pulse sensor.
1. Make sure that the power cord is unplugged.
Remove the 3/4” Screw (33) and the Access Door
(105) from the Console Back (104).
2. Connect the wire on the receiver (A) to the indicated
wire extending from the Console Back (104). Remove
the paper from the adhesive pad on the back of the
receiver. Hold the receiver so the small cylinder is
near the lower edge of the receiver and is facing
the Console Back as shown. Firmly press the re-
ceiver onto the indicated corner of the Access Door
(105). Note: If there are two screws included with the
chest pulse sensor and two plastic posts on the inside
of the Access Door, attach the receiver to the plastic
posts on the Access Door with the two screws.
3.
Make sure that no wires are pinched. Reattach the Access Door (105) with the 3/4” Screw (33). The other
wires included with the receiver may be discarded.
8. With the help of another person, hold the console as-
sembly near the right Upright (96) and the left Upright
(
not shown).
C
onnect the Wire Harness (118) to the wire harness in
the console assembly. Make sure to connect the con-
nectors properly (see the inset drawing); the con-
nectors should slide together easily and snap into
place. If the connectors do not slide together easily and
snap into place, turn one connector and try again. IF
THE CONNECTORS ARE NOT CONNECTED PROP-
ERLY, THE CONSOLE MAY BE DAMAGED WHEN
THE POWER IS TURNED ON.
Insert the excess wire
harness back into the right Handrail (108).
Set the console assembly on the right Upright (96) and the
left Upright (not shown). Thread two 1/4” x 1” Bolts (88)
with 1/4” Star Washers (87) into each side of the console
assembly. After you have started all four Bolts,
tighten them.
96
108
C
onsole
A
ssembly
118
87
88
118
8
Right Handrail
A
104
105
Cylinder
33
Wire
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-form 490 CX - PETL41105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-form 490 CX - PETL41105 in the language / languages: English as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pro-form 490 CX - PETL41105

Pro-form 490 CX - PETL41105 User Manual - German - 36 pages

Pro-form 490 CX - PETL41105 User Manual - Dutch - 36 pages

Pro-form 490 CX - PETL41105 User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info