553941
8
Zoom out
Zoom in
Previous page
1/36
Next page
8
7. Attach the Console Back (104) to the console assembly
with five 3/4” Screws (33). Be careful not to damage
any wires.
104
33
Console Assembly
33
33
7
5. See the inset drawing. Make sure that there are two U-
nuts (112) in the upper end of each Upright (96). Note:
Extra U-nuts may be included.
Identify the right and left Handrails (108) (there is an
i
dentification sticker on each Handrail). Hold the right
Handrail near the right Upright (96), and insert the Wire
Harness (118) into the large hole in the right Handrail
and out of the upper end as shown.
Next, hold the right Handrail (108) against the right
Upright (96). Tighten a 5/16” x 3 1/2” Bolt (121), with a
5/16” Washer (130), three to four turns into the right
Upright and the lower end of the right Handrail. Then,
tighten two 5/16” x 1” Bolts (113) into the upper end of
the right Handrail and the right Upright.
Be careful not
to drop the Bolts into the Handrail.
If necessary, raise
or lower the Handrail to thread the 5/16” x 1” Bolts into
the Upright. Firmly tighten all three Bolts.
Attach the left Handrail (108) to the left Upright (96) as
described above. Note: There is not a wire harness in the
left Upright.
6. See the inset drawing. Turn the Console (101) upside-
down on a soft surface. Remove the packing bands and
the Console Back (104).
If there are two Pulse Bar Screws (76) in each end of the
Console Frame (80), remove them. Hold the ends of the
Pulse Bar (77) against the Console Frame and attach the
Pulse Bar with the four Pulse Bar Screws. Firmly tighten
the Pulse Bar Screws. Be careful not to damage any
wires.
Locate the pulse wire extending from the Pulse Bar (77).
Insert the pulse wire under the Console Frame (80) and
plug the pulse wire into the indicated connector. The
pulse wire should slide easily into the connector and
snap into place; if it does not, turn the pulse wire and
then plug it in.
Attach the indicated ground wires to the Console Frame
(80) with a 1/2” Ground Screw (52).
5
96
118
96
108
108
1
13
1
13
121
Right
Left
121
119
112
130
130
76
52
77
101
80
6
104
101
Pulse
Wire
Connector
Ground
Wires
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-form 490 CX - PETL41105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-form 490 CX - PETL41105 in the language / languages: English as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pro-form 490 CX - PETL41105

Pro-form 490 CX - PETL41105 User Manual - German - 36 pages

Pro-form 490 CX - PETL41105 User Manual - Dutch - 36 pages

Pro-form 490 CX - PETL41105 User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info