8248
10
Zoom out
Zoom in
Previous page
1/50
Next page
10. After washing in water, apply shaver oil (provided with your shaver)
to the foil and trimmer blade, run the shaver without shaving for
approximately ten seconds. The wipe the surface of the foil and
trimmer blade with tissue or a soft cloth.
CARE OF THE FOIL, CUTTER AND TRIMMER
1. Always remove shaver from the charging base before cleaning.
2. Slide the switch to the OFF position, then remove the foil
holder and expose the trimmer.
3. Use the rotary washer provided to clean the foil holder,
cutter, trimmer and body.
4. After cleaning retract the trimmer to its original position
and replace the foil holder.
5. The shaver body may be wiped clean with a moist cloth
CAUTION: Never use alcohol, benzene or thinner.
REPLACING THE FOIL
1. Remove the foil holder
2. Remove the foil from protrusions of the foil holder.
The foil holder has one protrusion on the front and
two protrusions on the back.
3. Attach a new foil to the foil holder. Attach one depression
of the foil to one protrusion (on the front) of the foil holder
and two depressions to two protrusions on the back.
4. Attach the new foil holder.
CAUTION: Make sure the foil is attached properly.
REPLACING THE CUTTER
CAUTION: remove all hair / whiskers before removing the cutter.
(clumping of whiskers in the gear may result in shaver malfunction.)
1. Remove the cutter
2. Attach a new cutter
3. Insert the fixed plate horizontally into the mounting guide.
4. Insert the cutter shaft into the shaft slot.
CAUTION: Make sure cutter is securely inserted.
Improper assembly may result in malfunction of the shaver.
RECHARGEABLE BATTERY REMOVAL AND RECYCLING INSTRUCTIONS
PROCEDURE
CAUTION: To avoid a possible electric shock hazard, do not connect the
charging base after opening the shaver.
1. Slide the ON/OFF switch up to the ON position and discharge
the Ni-Cd batteries until the shaver stops operating.
2. Remove the front panel with a flat screwdriver.
3. Remove the two screws of bottom with a screwdriver,
and remove the movement unit.
4. Remove the Ni-Cd batteries and cut
The lead wire at the jointed position to the terminals
10
Starck_6005_IB_22-3-04 3/22/04 3:46 PM Page 10
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Princess 576005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Princess 576005 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info