793185
34
Zoom out
Zoom in
Previous page
1/124
Next page
34 Travel Scooter Series
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
DIAGNOSTIC CODES
The diagnostic codes for your Travel Scooter are designed to help you perform basic troubleshooting quickly
and easily. A diagnostic code will sound and/or ash in the event one of the conditions listed below develops.
Depending on the model you own, your Travel Scooter will communicate by one of the coding methods as follows:
1. A diagnostic code will begin, depending on model, with a series of fast beeps and/or fl ashes directly followed
by slower beeps and/or fl ashes which indicates the actual code. The code is only beeped and/or blinked once.
To repeat the diagnostic code, remove the key, then reinsert it and turn it to the “on” position, OR
2. A diagnostic code will identify the condition, pause, then repeat the code. The diagnostic code will continue
to alert you in this manner until the scooter is turned off .
NOTE: Your Travel Scooter will not run unless the diagnostic code condition is resolved and the Travel Scooter
has been turned off , then turned back on.
DIAGNOSTIC CODE CONDITION SOLUTION
(1)
Battery voltage is too low to operate the
Travel Scooter. Charge batteries as soon as possible.
■■
(2)
Battery charge is too low. Charge batteries.
■■■
(3)
The Travel Scooters battery voltage is too high
to operate the scooter, or the charger is still
connected to the off -board charger port.
Unplug charger and/or turn key off , then back on
again. If traveling down a slope, reduce Travel
Scooter speed to the minimum setting.
■■■■
(4)
Current limit time out. Turn the Travel Scooter off for a few minutes,
then turn your Travel Scooter back on.
■■■■■
(5)
The manual freewheel lever is in the (forward)
freewheel position. Remove the key from the key switch, then
push the manual freewheel lever to the drive
(rearward) position and restart your Travel
Scooter.
■■■■■
(6)
Throttle control lever not at center position at
start up. Verify that the batteries are fully charged. If
the batteries are fully charged, then return the
throttle control lever to center position, turn
Travel Scooter off then back on.
■■■■■■■
(7)
Speed pot error. Contact your authorized Provider for assistance.
■■■■■■■■
(8)
Motor volts error. Contact your authorized Provider for assistance.
■■■■■■■■■
(9)
Other internal errors. Contact your authorized Provider for assistance.
V I I . B A S I C T R O U B L E S H O OT I N G
What if my Travel Scooter does not move when I press the throttle control lever?
When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the motor/
transaxle assembly is cut.
Pull back on the manual freewheel lever, turn the Travel Scooter off , and then back on to return to normal
operation.
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pride Go Go Endurance at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pride Go Go Endurance in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 9.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pride Go Go Endurance

Pride Go Go Endurance User Manual - German, Dutch, Italian - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info