Manual Pride Colt Deluxe 2.0 (page 29 of 44) (English)

722005

Zoom out

Zoom in

1/44

Mid-size Scooter Series

V. COMFORT ADJUSTMENTS

Seat Height Adjustment—Comfort Seat Post

(If Equipped)

To reposition the seat to one of two different

heights:

1. Remove the seat from your scooter. Push

forward or pull upward and hold the seat

rotation lever to disengage the seat, then rotate

the seat and lift it off of the scooter.

2. Remove the rear shroud.

3. Push up the seat post boot to uncover the

hardware.

4. Push down on the seat post while loosening

and removing the shoulder bolt, washer, and

nut. See figure 18.

5. Remove the comfort spring.

6. To raise the seat to the top most mounting hole,

insert the height adjustment spacer. To lower

the seat to the lowest mounting hole, remove

the height adjustment spacer.

7. Reinstall the comfort spring.

8. Hold the upper seat post at the desired height

and match up the locating holes in the lower

seat post. Utilize the top holes for the upper

position or the bottom holes for the lower posi-

tion.

NOTE: When the seat post is mounted in the

upper position, you must utilize two spacers.

9. Press down on the seat post while reinstalling

the hardware and tightening to 210 in • lb (24

N • m).

10. Replace the rear shroud and the seat.

Figure 18. Seat Height Adjustment - Comfort Seat Post

Seat Suspension Adjustment (If Available)

You can loosen or stiffen the seat suspension based on which comfort spring you install.

To adjust the seat suspension:

1. Remove the seat from your scooter. Push forward or pull upward and hold the seat rotation lever to

disengage the seat, then rotate the seat and lift it off of the scooter.

2. Remove the rear shroud.

3. Push up the seat post boot to uncover the hardware.

4. Push down on the seat post while loosening and removing the hex head bolt and nut.

5. Remove the current spring.

6. Install the desired spring. See figure 18.

7. Press down on the seat post while reinstalling the hardware and tightening to 210 in • lb (24 N • m).

8. Replace the rear shroud and the seat.

IDENTIFICATION KEY

1. BOOT

2. UPPER SEAT POST

3. COMFORT SPRING

weight capacities: 0-220 lbs. (0-90.72 kg)

220-400 lbs. (90.72-181.44 kg)

4. SPACER

5. SHOULDER BOLT (210 in • lb [24 N • m])

6. LOWER SEAT POST

7. WASHER

8. NUT

I bought a 'new' Pride Colt Deluxe 2.0. Later I discovered that both Track Rods where they fit on the Track Rod Ends as best as I could see has some play in them. I rang up the Shop who supplied it, & they sent someone out with a Tie Rap, & then put one on each of them to hold them firmly together. My question is, is this standard procedure when dealing with Mobility Scooters, or are they manufactured 'disabled' to be like the Owner ? Submitted on 3-10-2024 at 20:35
Reply Report abuse
Console shows three green lights are out while charger is flashing fully charged Submitted on 15-10-2023 at 15:01
Reply Report abuse
How do I enable the scooter to go from pushing to driving mode? Submitted on 1-7-2023 at 19:42
Reply Report abuse
Why is my suspension on my pride deluxe Colt so tight Submitted on 21-9-2021 at 11:28
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pride Colt Deluxe 2.0 in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pride Colt Deluxe 2.0 Manual

Product: