691234

Precor C934 Manual

47
Zoom out
Zoom in
Previous page
1/60
Next page
page 47
COMMERCIAL PRODUCTS DIVISION
ALIGNING THE RUNNING BELT
The correct alignment of the running belt is critical to the smooth operation of the
treadmill. The belt is properly aligned at the factory. However, during shipping
and handling or by use on an uneven surface, the belt may move off center and
require a few simple adjustments.
Before aligning the running belt, check its operation by following the procedure in
Checking the Alignment of the Running Belt
on page 22. If you determine that
the belt needs alignment, follow the instructions here.
CAUTION: Special care must be taken when aligning the running belt. Turn
OFF the treadmill while adjusting or working near the rear roller. Remove
any loose clothing and tie back your hair. Be very careful to keep your
finger or any other object clear of the belt and rollers, especially in front of
the roller and behind the deck. The treadmill will not stop immediately if an
object becomes caught in the belt or rollers.
Realigning the belt takes a few simple adjustments. If you are unsure about this
procedure, call Precor Customer Support (see
Obtaining Service
on page 7.)
Take the following steps to align the running belt on the treadmill. To ensure your
safety, make all adjustments while the treadmill is OFF.
1. Make sure the treadmill is OFF and the running belt has completely stopped.
2. Locate the left belt adjustment bolt in the rear end cap of the treadmill. (To
determine left and right, stand at the rear of the treadmill and face the display.)
The direction you turn the bolt depends on how the belt is tracking. Make all
belt adjustments on the
left rear corner bolt
using the hex key provided.
• If the belt is off center to the LEFT, turn the adjusting bolt ¼ turn clock-
wise, which moves the running belt to the right.
• If the belt tracks off center to the RIGHT, turn the bolt ¼ turn
counter-
clockwise
; this moves the belt to the left.
Important: Do not turn the adjusting bolt more than ¼ turn at a time. Over-
tightening the bolt can damage the treadmill.
3. Turn ON the treadmill, press QUICKSTART, and then increase the running
belt speed to 3 mph (5 kph) by pressing SPEED ▲.
CAUTION: Stand to the side of the treadmill. The running belt begins
moving automatically after you press QUICKSTART.
4. Observe the running belt for a couple of minutes. The belt should be centered
on the running bed. A few inches from either side of the side rail platform.
CAUTION: If you hear any chafing or the running belt appears to be
getting damaged, stop the running belt immediately by pressing the
red Stop key. Contact Precor Customer Support.
5. If the belt needs additional alignment, repeat steps 1 through 4 of this
procedure until the belt is properly aligned.
6. Press the red Stop button. To return to the Precor banner, press RESET.
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Precor C934 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Precor C934 in the language / languages: English as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info