685350
27
Zoom out
Zoom in
Previous page
1/204
Next page
6 OPERATING THE ENGINE
ENGLISH
STOPPING THE ENGINE CHECKS DURING OPERATION
While running, make the following checks to see that all
parts are working correctly.
BRadiator Cooling water(Coolant)
WARNING
To avoid personal injury:
A Do not remove radiator cap until
coolant temperature is well below
its boiling point. Then loosen cap
slightly to the stop position, to
relieve any pressure, before
removing cap completely.
If the coolant temperature warning lamp lights up or if
steam or coolant does not stop squirting from the
radiator overflow pipe, turn off the load and keep the
engine idling (COOLING-DOWN) for at least 5
minutes to let it cool down gradually. Then stop the
engine and take the following inspection and servicing.
1. Check to see if the coolant runs short or if there is any
coolant leak;
2. Check to see if there is any obstacle around the
cooling air inlet or outlet;
3. Check to see if there is any dirt or dust between
radiator fins and tube;
4. Check to see if the fan belt is too loose; and
5. Check to see if radiator water pipe is clogged.
BOil pressure lamp
The lamp lights up to warn the operator that the engine
oil pressure has dropped below the prescribed level. If
this should happen during operation or should not go off
even after the engine is accelerated more than
1000rpm, immediately stop the engine and check the
following:
1. Engine oil level (See "ENGINE OIL" in "PERIODIC
SERVICE" section.)
BCharge lamp
The lamp lights up to warn the operator that the battery
charge is low. If this should happen during operation,
immediately stop the engine and check the following:
1. Cable broken
2. Poor connection at alternator terminal
3. Fan belt too loose or damaged
1. Return the speed control lever to low
idle, and run the engine under idling
conditions.
A If equipped with a turbo-charger, allow the engine
to idle for 5 minutes before shutting it off after a full
load operation.
Failure to do so may lead to turbo-charger trouble.
2. The engine should stop with the starter
switch placed at the OFF position. (In
case of non-stopping, set the engine
stop lever to the "STOP" position
manually.)
3. After stopping the engine, remove the
key.(Be sure to return the engine stop
lever to the START position to be ready
for the next starting in case of manually
stopping.)
(1) Speed control lever
(2) Engine stop lever
(A) "IDLING"
(B) "OPERATION"
(C) "START"
(D) "STOP"
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PowerTech PTS-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PowerTech PTS-40 in the language / languages: English as an attachment in your email.

The manual is 14,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info