685350
26
Zoom out
Zoom in
Previous page
1/204
Next page
5OPERATING THE ENGINE
ENGLISH
(with lamp timer in use)
A The glow lamp goes out in about 5 seconds when
the lamp timer is up. Refer to this for pre-heating.
Even with the glow lamp off, the glow plug can be
pre-heated by turning the starter switch to the "PRE-
HEATING" position.
A If the oil pressure lamp should be still on,
immediately stop the engine and check;
- if there is enough engine oil.
- if the engine oil has dirt in it.
- if the wiring is faulty.
A If the glow lamp should redden too quickly or too slowly,
immediately ask your KUBOTA dealer to check and
repair it.
A If the engine does not catch or start at 10 seconds
after the starter switch is set at "STARTING"
position, wait for another 30 seconds and then begin
the engine starting sequence again. Do not allow the
starter motor to run continuously for more than 20
seconds.
COLD WEATHER STARTING
If the ambient temperature is below -5°C(23°F)* and the
engine is very cold, start it in the following manner:
Take steps (1) through (4) above.
A Shown below are the standard preheating times for
various temperatures. This operation, however, is
not required, when the engine is warmed up.
A Do not allow the starter motor to run continuously for
more than 20 seconds.
A Be sure to warm up the engine, not only in winter, but
also in warmer seasons. An insufficiently warmed-up
engine can shorten its service life.
A When there is fear of temperature dropping below
-15°C (5°F) detach the battery from the machine,
and keep it indoors in a safe area, to be reinstalled
just before the next operation.
4. Insert the key into the key switch and
turn it "ON".
(A) "SWITCHED OFF"
(B) "OPERATION"
(C) "PREHEATING"
(D) "STARTING"
(A) "PREHEATING"
(B) "SWITCHED OFF"
(C) "OPERATION"
(D) "STARTING"
5. Turn the starter switch to the
"PREHEATING" position to allow the
glow lamp to redden.
6. Turn the key to the "STARTING"
position and the engine should start.
Release the key immediately when the
engine starts.
7. Check to see that the oil pressure lamp
and charge lamp are off. If the lamps are
still on, immediately stop the engine,
and determine the cause.
(See "CHECKS DURING OPERATION" in
"OPERATING THE ENGINE" section.)
8. Warm up the engine at medium speed
without load.
5. Turn the key to the "PREHEATING"
position and keep it there for a certain
period mentioned below.
Ambient
temperature
Preheating time
V3600-E3
V3600-T-E3
V3300-E3BG
V3600-T-E3BG
V3800-DI-T-E3
V3800-DI-T-E3BG
Above 10°C (50°F)
NO NEED
10°C (50°F) to
-5°C (23°F)
Approx.5
seconds
Approx.15
seconds
Below
-5°C (23°F)
Approx.10
seconds
Approx.30
seconds
Limit of
continuous use
20 seconds 30 seconds
6. Turn the key to the "STARTING"
position and the engine should start.
(If the engine fails to start after 10 seconds,
turn off the key for 5 to 30 seconds. Then
repeat steps (5) and (6).)
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PowerTech PTS-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PowerTech PTS-40 in the language / languages: English as an attachment in your email.

The manual is 14,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info