481029
14
Zoom out
Zoom in
Previous page
1/22
Next page
POWXQ5350 EN
Copyright © 2014 VARO P a g e | 14 www.varo.com
HAZARD! The saw blade is exposed much more than normally when
making a double mitre cut, which leads to an increased risk of injuries.
Always keep sufficient distance from the saw blade.
Starting position:
o Saw head completely raised.
o Mitre saw locked in the desired position.
o Saw head tilted at the desired angle, in relation to the surface of the workpiece, and
locked in position.
11.1.9 Sawing the workpiece:
Hold the workpiece against the mitre and width guide. If possible, use a work clamp for
fastening the workpiece.
Push on the upper half of the ON/OFF switch and push on the safety lock.
Lower the saw head carefully and completely downwards, while firmly holding onto the
handgrip. You should only apply minimum pressure while sawing, so as to prevent the
motor from slowing down.
Saw the workpiece in one single movement.
Carefully let the saw head return to its topmost starting position.
If further sawing works do not have to be carried out immediately, switch the saw OFF.
11.1.10 Illuminating the work area (26)
Provide for sufficient lighting of the direct working area.
For this, switch on the lighting unit with the light switch.
Loosen the lock screw and move the lighting unit so that the illumination of the working
area is optimal.
Retighten the lock screw again
If required, each lamp can be aligned individually.
Note: for larger vertical bevel angles, pay attention that the lighting unit
does not collide with the workpiece or the fence during sawing.
11.1.11 Marking the cutting line (14)
A laser beam indicates the cutting line of the saw blade. This allows for exact positioning of
the workpiece for sawing, without having to open the retracting blade guard.
For this, switch the laser beam on with the switch
Align the cutting mark on your workpiece with reference to the right-hand edge of the laser
line.
Before sawing, check if the cutting line is still indicated correctly. The laser beam, as an
example, can be misadjust due to vibrations after intensive use.
11.2 Table saw mode (Fig. 7)
11.2.1 Safety instructions for the saw blade guard
The saw blade guard protects against accidental contact with the saw blade and prevents
wood splinters from flying about.
Make sure that the saw blade guard is always installed while working.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5350 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5350

Powerplus POWXQ5350 User Manual - German - 23 pages

Powerplus POWXQ5350 User Manual - Dutch - 23 pages

Powerplus POWXQ5350 User Manual - French - 22 pages

Powerplus POWXQ5350 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info