481029
10
Zoom out
Zoom in
Previous page
1/22
Next page
POWXQ5350 EN
Copyright © 2014 VARO P a g e | 10 www.varo.com
Note: The essential operating components of the machine are presented in
this section. Make sure to read this section, before you use the machine for
the first time.
10.2.1 Table saw operating mode
Make sure that the table is mounted completely and in the right direction and that the
locking pin is properly locked.
Release the table stops, so that you can push down the table. Then lock with stops. (8&9)
The ON/OFF switch is used for starting and stopping the machine. (1&2)
10.2.2 Cross-cut and mitre saw operating mode
Release the table stops so that the table can be pushed up by springs. After that lock with
the stop.
Remove the lower saw blade guard. (41)
For starting the motor, push on the switch in the handgrip. (13)
To switch off the motor, release the switch.
10.2.3 Turntable (16)
The turntable can be turned 49° to the left and 49° to the right, and it can be fixed in preset
positions of 0°, 15°, 22.5°, 30° and 45°.
For turning the mitre table, the locking knob must be released.
To prevent that the mitre angle changes while sawing, the locking knob of
the mitre saw must be tightened (also when the saw has been fixed at a
preset stop).
10.2.4 Adjustment of the bevelling angle
The support arm can be tilted vertically and in an angle of 45° to the left.
To be able to tilt the support arm, the bevel lock must be released.
To prevent the bevel angle from changing while sawing, the locking knob of
the support arm must be tightened.
10.2.5 Mitre and width guide
The mitre and width guide is mounted on the top saw table. The mitre and width guide locking
knob must point towards the front of the machine.
Once the locking knob is released, the mitre and width guide can be removed.
10.2.6 Connection to a dust collector
The dust of some types of wood (such as for instance beech, oak and ash)
can be hazardous if inhaled. Always use a dust collector:
If the saw is set up in an enclosed space;
Whenever the saw is being used for longer periods of time (more than a half hour per
day);
When sawing oak-, beech- or ashwood.
The dust collector must conform to the following requirements:
The diameter of the dust exhaust pipe must fit properly (34 mm);
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5350 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5350

Powerplus POWXQ5350 User Manual - German - 23 pages

Powerplus POWXQ5350 User Manual - Dutch - 23 pages

Powerplus POWXQ5350 User Manual - French - 22 pages

Powerplus POWXQ5350 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info