582100
9
Zoom out
Zoom in
Previous page
1/20
Next page
POWXG3025 EN
Copyright © 2015 VARO P a g e | 9 www.varo.com
Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the
correct length.
To increase the life of the cord it can be soaked in water for a couple of days. This will make
the line tougher so that it lasts longer.
10 CUTTING EQUIPMENT (LONG REACH HEDGE TRIMMER)
To ensure good cutting results it is important that the contact pressure between the blades is
correct. The contact pressure is adjusted by turning the screws on the underside of the bar
clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn. Lock the
screws using the locking nut on the top of the bar. Check that the screws are loose enough to
allow the washers under the screw heads to slide sideways.
When the blades are correctly adjusted the play between the blades should be 0,20,4 mm,
measured at the screws.
The edges of the blades are too hard to be filed. Dull blades should be sharpened using a
grinder.
Replace the blades if they are bent or damaged.
11 OPERATING INSTRUCTIONS
11.1 Prepare the machine
11.1.1 Assembling the Front handle
Fit the front handle absorber (A) on the rear tube (C). While aligning the hole (B) on the front
handle absorberthe position pin (F) on the barrier (E) and one position hole (D) of three on
the rear handle, fit the barrier on the rear handle and insert the position pin into the position
hole on the rear handle. Make sure the barrier on the left side of the machine. (Fig. 10)
Push down the front handle (G), and then turn four screws (H) clockwise to tighten the front
handle securely. (Fig. 11)
11.1.2 Connecting the tube (Fig. 12)
Align the hole (A1) on the front tube (A) and the lock pin (B). Then, Pull out the Lock pin, and
while inserting the front tube in the connector (D) to the end. After loosened the lock pin, it will
return to its original position automatically, and insert into the hole on the front tube.
Make sure the front tube can’t be rotated after the lock pin came back to its original position.
Turn the lock knob (C) clockwise to tighten the front tube securely.
11.1.3 Fitting blades and trimmer heads
When fitting the cutting attachment it is extremely important that the raised
section on the top clamping plate/support flange engages correctly in the
centre hole of the cutting attachment. If the cutting attachment is fitted
incorrectly it can result in serious and/or fatal personal injury.
Never use a cutting attachment without an approved guard. See the chapter
on Technical data. If an incorrect or faulty guard is fitted this can cause
serious personal injury.
11.1.4 Fitting the guard extension
The guard extension shall always be fitted when using the trimmer head and combination
guard. The guard extension shall always be removed when using the grass blade. (Fig.
13)
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG3025 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG3025 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG3025

Powerplus POWXG3025 User Manual - German - 22 pages

Powerplus POWXG3025 User Manual - Dutch - 22 pages

Powerplus POWXG3025 User Manual - French - 22 pages

Powerplus POWXG3025 Additional guide - All languages - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info