517145
7
Zoom out
Zoom in
Previous page
1/11
Next page
POWXG1065 EN
Copyright © 2017 VARO P a g i n a | 7 www.varo.com
8.1 Switching on and off
Make sure mains voltage coincides with that indicated on machine’s
specification plate.
Make sure “on/off” switch (see A no. 1) is switched off (set to “0”) before
connecting to mains outlet.
Connect machine to mains outlet.
To switch on, set “on/off” switch to “I” position; the machine starts (see A no. 1).
To switch off, set “on/off” switch to “0” position; the machine stops (see A no. 1).
The grinder will still continue to run after the machine has been switched
off. Risk of injury.
Testing the grinder:
Before using for the first time, and each time the grinding wheel is changed, test by letting
grinder spin freely for at least 30 seconds. Switch machine off if wheel rotation is not round, if
significant oscillations are noticeable, or if machine makes abnormal noises.
8.2 Sharpening saw chains (Fig C)
Incorrect sharpening of the saw chain can lead to a damaged chain, increasing the risk of
the saw bucking!
Ensure the chain is precisely adjusted.
Take correct grinding angle and the saw chain’s minimum dimensions into consideration.
Remove as little matter as possible.
Do not grind non-cutting or connection links, to avoid cracking chain.
Negligence could lead to risk of accident when using the chainsaw.
8.3 Sharpening instructions
After sharpening, all cutting links must be of equal length and width.
Chain is worn down and must be replaced with new one when saw teeth are less than
4mm long.
Make sure suspended transparent safety guard moves freely and does not get stuck. Do
not overly tighten safety guard fastening screws (see figure A no. 6).
8.3.1 Inserting saw chain:
Unscrew clamp screw (9) and position saw chain on guide rail (12). The saw teeth must
be facing the grinding wheel (8).
Click chain stop (10) down and pull saw chain back until saw tooth to be sharpened (25)
rests against chain stop (see figure1).
8.3.2 Setting grinding angle:
Set required grinding angle using rotation table (14) and angle gauge (16).
8.3.3 Adjusting chain stop:
Lower grinding head (2). Turn adjusting screw (11) until saw tooth (25) rests against
grinding wheel (8) (see figure 2.
Clamp chain link by turning clamp screw (9).
Adjust grinder depth stop using adjusting screw (18) in such a way that grinding wheel (8)
touches base of saw tooth (see figure 2).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG1065 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG1065 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG1065

Powerplus POWXG1065 User Manual - German - 11 pages

Powerplus POWXG1065 User Manual - Dutch - 11 pages

Powerplus POWXG1065 User Manual - French - 12 pages

Powerplus POWXG1065 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info