517142
8
Zoom out
Zoom in
Previous page
1/14
Next page
POWXG1006 EN
Copyright © 2015 VARO P a g e | 8 www.varo.com
9.2 Tensioning the saw chain
Always pull the plug out of the power socket before doing any work on the
chainsaw!
Wear safety gloves!
Make sure the saw chain (4) is inside the guide groove of the guide bar (7) (Fig.1 a)!
Turn the outer Knob clockwise until the saw chain is correctly tensioned, then rotate the inside
knob (5) to block the guide bar in that position.
While the inside knob is being tightened, the guide bar must then be pushed upwards.
Check the chain tension again (see Fig. 3). Do not tension the chain too tightly.
When cold, it should be possible to lift the chain in the middle of the guide bar approx. 5 mm.
Tighten the lock nut (5) securely.
When warm, the saw chain will expand and slacken and there is a danger of it jumping off the
rail altogether. Re-tension if necessary.
If the saw chain is re-tensioned when hot, it must be loosened again when the sawing work
has been completed. Otherwise, the contraction which takes place as the chain cools would
result in excessively high tension.
A new saw chain requires a running-in period of approx .5 minutes. Chain lubrication is very
important at this stage. After running in, check chain tension and re-tension if necessary.
9.3 Filling in chain oil (Fig 4)
To prevent dirt getting inside the tank, clean the oil tank cap (21) before opening. Check the
contents of the oil tank during sawing work by checking the oil gauge (15). Close the oil tank
cap tightly and wipe away any spills.
9.4 Securing the extension lead (Fig 6)
Only use extension leads suitable for outdoor use. The cross section of the cable (max. length
of extension cord: 75m) must be at least 1,5 mm². secure the chainsaw flex to the extension
lead by inserting the extension lead into the strain relief gap of the housing.
Extension leads longer than 30 m will reduce the performance of the chainsaw.
9.5 Chain lubrication
To prevent excessive wear, the saw chain and guide bar must be evenly lubricated during
operation.
Lubrication is automatic. Never work without chain lubrication. If the chain runs dry, the entire
cutting apparatus will quickly become severely damaged. It is therefore important to check
both chain lubrication and the oil gauge every use (Fig. 4).
Never use the saw when the oil level is below the Min. mark.
Min.: When only approx. 5 mm of oil is visible at the lower rim of the oil gauge (15), you
must top up with oil.
Max.: Top up with oil until the window is full.
9.6 Checking the automatic lubrication
Before commencing work, check the automatic chain lubrication and oil gauge. Switch on the
chain saw and hold it above the ground. Be careful not to allow the chain saw to touch the
ground. For safety reasons it is best to keep a clearance of at least 20 cm. If you now see
growing traces of oil, the chain lubrication system is working correctly. if there are no traces of
oil at all, try cleaning the oil outlet (Fig 2, C), the upper chain tensioning borehole (E) and the
oil duct, or contact your Customer Service.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG1006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG1006 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG1006

Powerplus POWXG1006 User Manual - German - 15 pages

Powerplus POWXG1006 User Manual - Dutch - 15 pages

Powerplus POWXG1006 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info