517142
7
Zoom out
Zoom in
Previous page
1/14
Next page
POWXG1006 EN
Copyright © 2015 VARO P a g e | 7 www.varo.com
7 TRANSPORTING THE CHAINSAW
Before transporting the chainsaw, always remove the plug from the power socket and slide the
chain guard over the rail and chain. If several cuts are to be performed with the chain saw, the
saw must be switched off between cuts.
8 BEFORE STARTING UP
The voltage and current supply must comply with the ratings on the type plate.
Before commencing work, always check that the chainsaw works properly and is safe to
operate.
Check also that the chain lubrication and the oil gauge are in good working order (see
Fig.4). When the oil lever is approx. 5 mm from the bottom mark, you must top up with oil.
When the oil level is higher you can work without worry.
Switch on the chain saw and hold it above the ground. Be careful not allow the chainsaw
to touch the ground. For safety reasons it is best to keep a clearance of at least 20 cm. If
you now see growing traces of oil, the chain lubrication system is working correctly. If
there are no traces of oil at all, try cleaning the oil outlet (Fig 2, C), the upper chain
tensioning borehole (E) and the oil duct, or contact your Customer Service. (Be sure to
read the section “Filling in chain oil and chain lubrication” on this point).
Check the chain tension and retention, if necessary (see the section “Tensioning the saw
chain” on this point).
Make sure the chain brake is working properly (see also the section “Releasing the chain
brake”).
9 ASSEMBLY
9.1 Fitting the guide bar and chain (Fig 1, 2, 3)
If the chain saw is already connected to the power supply: Pull the plug
from the socket outlet. Wear protective gloves whenever doing any work on
the saw chain.
Important: The front finger guard (3) must always be in the top (vertical) position (Fig. 5).
The guide bar and saw chain are supplied separately. To assemble, first unscrew the lock nut
(5) and remove the guide bar cover (6). The guide bolt (17) must be in the centre of the guide.
If necessary, adjust the chain tensioning with the chain wheel (16).
To prevent injury on the sharp cutting edges, always wear gloves when
assembling, tensioning and checking the chain.
Before assembling the guide bar with the saw chain, check the cutting direction of the teeth!
The running direction is marked with an arrow on the cover (6) (Fig 3, G). To determine the
direction of cut, it may be necessary to turn over the saw chain (4). Hold the guide bar (7)
vertically with the tip pointing upwards and put on the saw chain (4, beginning at the tip of the
bar.
Then assemble the guide bar with the saw chain as follows:
Place the guide bar with the saw chain on the chain wheel (16) and guide bolt (17).
Place the saw chain round the chain wheel (16) and make sure it is correctly mounted (see
Fig.1, A).
Place the cover (6) on top and tighten gently with the lock nut (5). Now the saw chain has
to be correctly tensioned.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG1006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG1006 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG1006

Powerplus POWXG1006 User Manual - German - 15 pages

Powerplus POWXG1006 User Manual - Dutch - 15 pages

Powerplus POWXG1006 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info