582667
11
Zoom out
Zoom in
Previous page
1/14
Next page
POWX1365MB EN
Copyright © 2015 VARO P a g e | 11 www.varo.com
13.4 Cutting with workbench
WARNING: Always cut in a forward direction. Never draw the tool
backwards. If you are a novice user, practice by cutting thin wood until
proficient.
Set cutting angle of workbench. (See Cutting angle adjustment Section)
Place the work-piece onto the workbench and clamp the work-piece with clamp
subassembly (20). (See Installing and adjusting the clamp Section)
NOTE: if the length of the work-piece is longer than normal level, you can
use extended function of extension rod (23), hold the Tiltable support (24)
and pull the extension rod to a suitable position for current work-piece.
(Refer to Fig. 9 and Fig. 10)
Fit the correct blade ensuring it is sharp and not damaged.
Set the depth of cut. (See Setting the Cutting Depth Section)
Grasp the tool firmly (See Holding and Switching ON/OFF Section), switch on the tool and
wait for a moment for the blade to run up to speed. Next, depress the safety lock button
(3) and plunge the blade into the material slowly and gently, but firmly. Then push the tool
forwards along the guide rails (19) to be cut.
NOTE: Never draw the tool backwards.
Once the cut has been finished, lift the tool from the workbench before switching off. If a
lot of dust has been created, keep switched on for a few seconds extra to allow the dust to
clear from within the tool.
NOTE: if cutting without workbench, you can refer to the below
descriptions:
Check the blade whether is correct and ensuring it is sharp and not damaged.
Set the depth of cut, switch on the tool and wait for a moment for the blade to run up to
speed.
Depress and hold the safety lock button (3) on, plunge the blade into the material slowly
and gently, but firmly.
Push the tool forwards along the line to be cut. If necessary, switch on the laser generator
(1). (Refer to Laser line generator Section)
14 CLEANING AND MAINTENANCE
Regular cleaning is required for the safe operation of the tool, as an excessive build up of dust
will prevent the tool from operating correctly.
The dust extraction hose (b) may block and require cleaning occasionally, especially if damp
wood is being cut.
Unplug from mains supply.
Clean thoroughly with a small soft brush, like a paint brush.
Keep the cooling vents on the motor housing clean and unobstructed at all times.
Never use any caustic agents or solvents to clean the plastic parts.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX1365MB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX1365MB in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX1365MB

Powerplus POWX1365MB User Manual - German - 15 pages

Powerplus POWX1365MB User Manual - Dutch - 15 pages

Powerplus POWX1365MB User Manual - French - 15 pages

Powerplus POWX1365MB Additional guide - All languages - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info