645723
9
Zoom out
Zoom in
Previous page
1/12
Next page
POWX1340 EN
Copyright © 2015 VARO P a g e | 9 www.varo.com
8.2 Sharpening the chain
Set your saw on a flat, solid surface. For proper sharpening the chain tension should be
adjusted (as specified in the chainsaw instruction manual). Sharpening will be best
accomplished if done on the flat of the saw bar somewhere near the middle of the bar.
Position the saw so that you are looking at the side of the chain bar with the motor to your
right. Cutter teeth on the far side of the chain are sharpened, from inside to outside as
shown in figure 5. Lay the guide (B) flat on the tooth with the 30° index line (L) parallel
with the chain. Align the index line with the chain. Two or three light strokes are usually
enough unless the cutters have been damaged. Sharpen all cutters equal. Start with the
cutter with the most visual damage (i.e. nicks or gouges) and sharpen all cutters equally.
Do not remove excessive material as this only shorten the life of the chain.
Sharpen cutter teeth (J) only, not the depth gauge (K)
When all of the teeth on the top of the bar have been sharpened, advance the chain using
a glove or a rag by pulling the chain toward the end of the bar. Repeat until all the teeth
on the far side of the chain have been sharpened.
Turn the saw around so you are looking at the side of the chain bar with the motor to your
left. Sharpen the cutter teeth on the far side of the chain, from inside to outside, or away
from you (figure 6). Lay the guide flat on the tooth with the 30° index line parallel with the
chain. Repeat the process above to sharpen all of the cutter teeth on the far side of the
chain.
After your chain has been sharpened a number of times, you may fin that it does not cut
as fast as you feel it should. Each cutter on your chain has a depth gauge (K) just ahead
of the cutting edge (J) that determines how big a bite it can take. To check for proper
depth of the cut, lay a metal straight edge across the tops of the cutting edges (Figure 7),
and check the dimension indicated. This dimension should be approximately equal to the
thickness of the gauge (K). if it is not, grind the chain depth gauge until the clearance is
approximately equal to the thickness of the sharpening kit gauge. Be careful to maintain
its shape. Do not remove more material. Houd de instelling van de dieptemaat gelijk bij
alle zaagtanden, om rechte zaagsneden te kunnen maken.
9 OPERATION
9.1 On / off switch (Pic. 3)
Always check that the power supply corresponds to the voltage on the
rating plate.
Turning on: Turn the power button to position I
Turning off:Turn the power button to position O
9.2 Setting the speed (Pic. 4)
The multi tool speed is continuously adjustable. Always start from the lowest speed and
then increase the speed to the desired level.
“+” denotes the higher speed
-” denotes the lower speed
9.3 LED light (Pic. 5)
If you work in dark condition and want see clearly the work area ,please turn on the LED
Push the LED button (6),the LED is on
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX1340 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX1340 in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX1340

Powerplus POWX1340 User Manual - German - 14 pages

Powerplus POWX1340 User Manual - Dutch - 13 pages

Powerplus POWX1340 User Manual - French - 13 pages

Powerplus POWX1340 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info