480927
14
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0782 EN
Copyright © 2015 VARO P a g e | 14 www.varo.com
10.1.8 Double mitre cut
A double mitre cut is a combination of a mitre cut and a bevelling cut; this means that the
workpiece is cut at an angle in the one single movement, which is not equal to 90° in
relation to the mitre and width guide and the material surface.
HAZARD! The saw blade is exposed much more than normally when
making a double mitre cut, which leads to an increased risk of injuries.
Always keep sufficient distance from the saw blade.
Starting position:
- Saw head completely raised.
- Mitre saw locked in the desired position.
- Saw head tilted at the desired angle, in relation to the surface of the workpiece, and locked in
position.
10.1.9 Sawing the workpiece:
Hold the workpiece against the mitre and width guide. If possible, use a work clamp for
fastening the workpiece.
Push on the upper half of the ON/OFF switch and push on the safety lock.
Lower the saw head carefully and completely downwards, while firmly holding onto the
handgrip. You should only apply minimum pressure while sawing, so as to prevent the
motor from slowing down.
Saw the workpiece in one single movement.
Carefully let the saw head return to its topmost starting position.
If further sawing works do not have to be carried out immediately, switch the saw OFF.
10.2 Table saw mode
10.2.1 Safety instructions for the saw blade guard (Fig. 12)
The saw blade guard (3) protects against accidental contact with the saw blade and prevents
wood splinters from flying about.
Make sure that the saw blade guard is always installed while working.
10.2.2 Riving knife (Fig. 12)
The riving knife (2) prevents that a workpiece is grasped by the rising teeth of the saw
blade and is thrown in the direction of the operator.
Always make sure that the riving knife is installed while working with the saw.
10.2.3 Lower saw blade guard (Fig. 12)
The lower saw blade guard (14) is designed to provide protection against accidental
contact with the saw blade.
The safety saw blade guard must always be installed, while the machine is in operation.
10.2.4 Push block (Fig. 17 and 18)
A push block (24) serves as an extension of the hand and protects against accidental
contact with the saw blade.
Always use a push block, when the interval between the saw blade and the mitre and
width guide is less than 120 mm.
Use the push block at an angle of 20° to 30° in relation to the surface of the saw table.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0782 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0782 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0782

Powerplus POWX0782 User Manual - German - 24 pages

Powerplus POWX0782 User Manual - Dutch - 23 pages

Powerplus POWX0782 User Manual - French - 24 pages

Powerplus POWX0782 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info