480927

Powerplus POWX0782 Manual

10
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0782 EN
Copyright © 2015 VARO P a g e | 10 www.varo.com
9.2.2 Cross-cut and mitre saw operating mode (Fig. 6)
Make sure that the mitre and width guide (4) is correctly installed and that the saw blade is
covered. This activates switch A (8). Make sure that the cover (mitre and width guide) is
firmly attached. If this is not the case, use the mitre and width guide locking knob (5) to
fasten it.
Remove the lower saw blade guard (14).
For starting the motor, push on the switch (29) in the handgrip.
To switch off the motor, release the switch (20).
9.2.3 Turntable (Fig. 7-9)
The turntable (11) can be turned 50° to the left and 60° to the right, and it can be fixed in
preset positions of 0°, 15°, 22.5°, 30°, 45° and 60°.
For turning the mitre table, the locking knob (9) must be released.
To prevent that the mitre angle changes while sawing, the locking knob of
the mitre saw must be tightened (also when the saw has been fixed at a
preset stop).
9.2.4 Adjustment of the bevelling angle (Fig. 10-11)
The support arm can be tilted vertically and in an angle of 45° to the left.
To be able to tilt the support arm, the bevel lock (16) must be released.
To prevent the bevel angle from changing while sawing, the locking knob of
the support arm must be tightened.
9.2.5 Mitre and width guide (Fig. 12-13)
The mitre and width guide (4) is mounted on the top saw table (1). The mitre and width guide
locking knob (5) must point towards the front of the machine.
The mitre and width guide is positioned over the saw blade guard (3). When the mitre and
width guide is installed, you must always make sure that the guide is fastened with the locking
knob.
Once the locking knob is released, the mitre and width guide (4) can be removed and the
switch (20) can be activated.
9.2.6 Connection to a dust collector
The dust of some types of wood (such as for instance beech, oak and ash)
can be hazardous if inhaled. Always use a dust collector:
If the saw is set up in an enclosed space;
Whenever the saw is being used for longer periods of time (more than a half hour per
day);
When sawing oak-, beech- or ashwood.
The dust collector must conform to the following requirements:
The diameter of the dust exhaust pipe must fit properly (43 mm);
The air flow volume must exceed 550m³/h;
The vacuum at the dust exhaust exit must be ≥ 740 Pa;
The air speed at the dust exhaust exit must be ≥ 20 m/s;
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0782 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0782 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0782

Powerplus POWX0782 User Manual - German - 24 pages

Powerplus POWX0782 User Manual - Dutch - 23 pages

Powerplus POWX0782 User Manual - French - 24 pages

Powerplus POWX0782 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info